[PATCH v2 04/15] arm64: dts: freescale: imx8mn-var-som: Update FEC support with MaxLinear PHY

[Frank Li]

On Mon, Jul 06, 2026 at 11:34:34AM +0200, Stefano Radaelli wrote:
> From: Stefano Radaelli <stefano.r at variscite.com>
>
> Update the FEC Ethernet controller on the i.MX8MN VAR-SOM to match the
> latest SOM hardware revision using the integrated MaxLinear MXL86110 PHY.
>
> Add the PHY VDDIO supply regulator and adjust reset timings.
>
> The PHY LED signals originate on the SOM, but the actual LEDs are part
> of the carrier implementation (RJ45 connector). Move the LED
> configuration to the Symphony carrier device tree, matching the
> evaluation board LED wiring.
>
> Wake-on-LAN via magic packet is not supported at the VAR-SOM level and
> is therefore not enabled in the SOM device tree nor in the official
> evaluation carrier board configuration (symphony).
> Designs requiring WoL support may enable it in their own carrier-specific
> device trees if properly integrated at the hardware level.
>
> Signed-off-by: Stefano Radaelli <stefano.r at variscite.com>
> ---
> v1->v2:
>  - Fixed commit message
>
>  .../dts/freescale/imx8mn-var-som-symphony.dts | 20 ++++++++++++++++++-
>  .../boot/dts/freescale/imx8mn-var-som.dtsi    | 20 ++++++++++---------
>  2 files changed, 30 insertions(+), 10 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
> index 7308613a48b2..520aff23e587 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
> @@ -8,6 +8,7 @@
>
>  /dts-v1/;
>
> +#include <dt-bindings/leds/common.h>
>  #include <dt-bindings/usb/pd.h>
>  #include "imx8mn-var-som.dtsi"
>
> @@ -74,7 +75,24 @@ reg_per_3v3: regulator-peripheral-3v3 {
>  };
>
>  &ethphy {
> -	reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>;

why remove this reset-gpios?

Frank

> +	leds {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		led at 0 {
> +			reg = <0>;
> +			color = <LED_COLOR_ID_YELLOW>;
> +			function = LED_FUNCTION_LAN;
> +			linux,default-trigger = "netdev";
> +		};
> +
> +		led at 1 {
> +			reg = <1>;
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_LAN;
> +			linux,default-trigger = "netdev";
> +		};
> +	};
>  };
>
>  &i2c2 {
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
> index 71a2f0866822..09146ab76385 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
> @@ -35,6 +35,13 @@ reg_3v3_fixed: regulator-3v3-fixed {
>  		regulator-max-microvolt = <3300000>;
>  		regulator-always-on;
>  	};
> +
> +	reg_phy_vddio: regulator-phy-vddio {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vddio-1v8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
>  };
>
>  &A53_0 {
> @@ -96,24 +103,19 @@ &fec1 {
>  	phy-mode = "rgmii";
>  	phy-handle = <&ethphy>;
>  	phy-supply = <&reg_eth_phy>;
> -	fsl,magic-packet;
>  	status = "okay";
>
>  	mdio {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
>
> -		ethphy: ethernet-phy at 4 { /* AR8033 or ADIN1300 */
> +		ethphy: ethernet-phy at 4 {
>  			compatible = "ethernet-phy-ieee802.3-c22";
>  			reg = <4>;
>  			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
>  			reset-assert-us = <10000>;
> -			/*
> -			 * Deassert delay:
> -			 * ADIN1300 requires 5ms.
> -			 * AR8033   requires 1ms.
> -			 */
> -			reset-deassert-us = <20000>;
> +			reset-deassert-us = <100000>;
> +			vddio-supply = <&reg_phy_vddio>;
>  		};
>  	};
>  };
> @@ -342,7 +344,7 @@ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
>  			MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
>  			MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
>  			MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
> -			MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x159
> +			MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
>  		>;
>  	};
>
> --
> 2.47.3
>
>