[PATCH v2 4/7] arm64: dts: mediatek: mt8186: Add and use UART AP_DMA controller

[AngeloGioacchino Del Regno]

This SoC has a DMA controller (AP_DMA) that provides one channel
for each data direction (transmit and receive) for all of the
UART controllers in the SoC.

In order to increase the efficiency of data TX/RX over the UART
controllers, add the UART DMA controller and assign the right
channels to each of the three UART controllers.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
---
 arch/arm64/boot/dts/mediatek/mt8186.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8186.dtsi b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
index fded6345d422..9fe60dee0b79 100644
--- a/arch/arm64/boot/dts/mediatek/mt8186.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
@@ -1142,6 +1142,22 @@ systimer: timer at 10017000 {
 			clocks = <&clk13m>;
 		};
 
+		apdma: dma-controller at 10200d80 {
+			compatible = "mediatek,mt8186-uart-dma", "mediatek,mt6835-uart-dma";
+			reg = <0 0x10200d80 0 0x80>, <0 0x10200e00 0 0x80>,
+			      <0 0x10200e80 0 0x80>, <0 0x10200f00 0 0x80>,
+			      <0 0x10200f80 0 0x80>, <0 0x10201000 0 0x80>;
+			interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_LOW 0>,
+				     <GIC_SPI 377 IRQ_TYPE_LEVEL_LOW 0>,
+				     <GIC_SPI 378 IRQ_TYPE_LEVEL_LOW 0>,
+				     <GIC_SPI 379 IRQ_TYPE_LEVEL_LOW 0>,
+				     <GIC_SPI 380 IRQ_TYPE_LEVEL_LOW 0>,
+				     <GIC_SPI 381 IRQ_TYPE_LEVEL_LOW 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			#dma-cells = <1>;
+			dma-requests = <6>;
+		};
+
 		gce: mailbox at 1022c000 {
 			compatible = "mediatek,mt8186-gce";
 			reg = <0 0X1022c000 0 0x4000>;
@@ -1218,6 +1234,8 @@ uart0: serial at 11002000 {
 			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART0>;
 			clock-names = "baud", "bus";
+			dmas = <&apdma 0>, <&apdma 1>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -1228,6 +1246,8 @@ uart1: serial at 11003000 {
 			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART1>;
 			clock-names = "baud", "bus";
+			dmas = <&apdma 2>, <&apdma 3>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -1482,6 +1502,8 @@ uart2: serial at 11018000 {
 			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART2>;
 			clock-names = "baud", "bus";
+			dmas = <&apdma 4>, <&apdma 5>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
-- 
2.54.0