[PATCH] dt-bindings: usb: Add Aspeed AST2700 DWC3 controller

[Ryan Chen]

The Aspeed AST2700 SoC integrates the Synopsys DesignWare USB3 core with
no vendor glue logic: it is functionally compatible with snps,dwc3, uses
the standard DWC3 clocks, and the only SoC-specific part is a USB3 PHY
that is handled by a separate driver.

Add a dedicated binding document rather than adding the compatible and a
conditional to snps,dwc3.yaml. This follows the established per-vendor DWC3
convention (apple,dwc3.yaml, socionext,uniphier-dwc3.yaml, ...) and keeps
the AST2700-specific constraints - notably the mandatory USB3 PHY - out of
the generic schema.

Signed-off-by: Ryan Chen <ryan_chen at aspeedtech.com>
---
The common DWC3 node properties are inherited from snps,dwc3.yaml via the
allOf $ref, so this schema only defines the additional AST2700-specific
constraints (the compatible, a single interrupt and the USB3 PHY) and does
not redefine the properties covered there. snps,dwc3.yaml is used rather
than snps,dwc3-common.yaml because the controller uses the standard DWC3
bus_early/ref/suspend clocks defined there.

Because reg, clocks and clock-names are only defined indirectly through
the $ref, they still appear in the required list, the same approach as
apple,dwc3.yaml.
---
 .../devicetree/bindings/usb/aspeed,dwc3.yaml       | 81 ++++++++++++++++++++++
 1 file changed, 81 insertions(+)

diff --git a/Documentation/devicetree/bindings/usb/aspeed,dwc3.yaml b/Documentation/devicetree/bindings/usb/aspeed,dwc3.yaml
new file mode 100644
index 000000000000..976f80b87e24
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/aspeed,dwc3.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/aspeed,dwc3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Aspeed SuperSpeed DWC3 USB SoC controller
+
+maintainers:
+  - Ryan Chen <ryan_chen at aspeedtech.com>
+
+description:
+  The common content of the node is defined in snps,dwc3.yaml.
+
+select:
+  properties:
+    compatible:
+      contains:
+        const: aspeed,ast2700-xhci
+  required:
+    - compatible
+
+properties:
+  compatible:
+    items:
+      - const: aspeed,ast2700-xhci
+      - const: snps,dwc3
+
+  interrupts:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: usb3-phy
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - resets
+  - phys
+  - phy-names
+
+allOf:
+  - $ref: snps,dwc3.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/aspeed,ast2700-scu.h>
+    #include <dt-bindings/reset/aspeed,ast2700-scu.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        usb at 12030000 {
+            compatible = "aspeed,ast2700-xhci", "snps,dwc3";
+            reg = <0x0 0x12030000 0x0 0x10000>;
+            interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&syscon0 SCU0_CLK_GATE_PORTAUSB2CLK>,
+                     <&syscon0 SCU0_CLK_U2PHY_REFCLK>,
+                     <&syscon0 SCU0_CLK_U2PHY_CLK12M>;
+            clock-names = "bus_early", "ref", "suspend";
+            resets = <&syscon0 SCU0_RESET_PORTA_XHCI>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&pinctrl_usb3axh_default &pinctrl_usb2axh_default>;
+            phys = <&uphy3a>;
+            phy-names = "usb3-phy";
+            dr_mode = "host";
+        };
+    };

---
base-commit: be5c93fa674f0fc3c8f359c2143abce6bbb422e6
change-id: 20260624-xhci-185ffd9ef8bd

Best regards,
-- 
Ryan Chen <ryan_chen at aspeedtech.com>