[PATCH v2 02/15] arm64: dts: freescale: imx8mn-var-som: move uSD support to carrier boards
Stefano Radaelli
stefano.radaelli21 at gmail.com
Mon Jul 6 02:34:32 PDT 2026
From: Stefano Radaelli <stefano.r at variscite.com>
The VAR-SOM-MX8MN module does not provide an onboard SD card slot.
USDHC2 is routed to the SD card slot on the carrier boards.
Move the USDHC2 node and pinctrl configuration from the SOM device tree
to imx8mn-var-som-symphony.dts and imx8mn-rve-gateway.dts, keeping the
SOM dtsi limited to hardware present on the module itself.
Add the required off-on-delay-us property for the USDHC2 regulator on
the Symphony carrier board.
Signed-off-by: Stefano Radaelli <stefano.r at variscite.com>
---
v1->v2:
- Update all the carrier boards and not only the symphony
.../boot/dts/freescale/imx8mn-rve-gateway.dts | 47 ++++++++++++++-
.../dts/freescale/imx8mn-var-som-symphony.dts | 57 +++++++++++++++++++
.../boot/dts/freescale/imx8mn-var-som.dtsi | 56 ------------------
3 files changed, 102 insertions(+), 58 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
index ea1855171fb0..056ea2f9e963 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
@@ -207,8 +207,16 @@ &usbotg1 {
/* SD interface on expansion connector. */
&usdhc2 {
- vmmc-supply = <®_3p3v>;
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC2>;
+ assigned-clock-rates = <200000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
cd-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
};
&iomuxc {
@@ -276,10 +284,45 @@ MX8MN_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x00000156 /* B */
>;
};
- /* Override Card Detect function GPIO value (GPIO1_IO10) from SOM: */
pinctrl_usdhc2_gpio: usdhc2gpiogrp {
fsl,pins = <
MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x41
>;
};
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
index b07e71d3adee..7308613a48b2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
@@ -28,6 +28,7 @@ reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
regulator-max-microvolt = <3300000>;
gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
+ off-on-delay-us = <20000>;
};
gpio-keys {
@@ -200,6 +201,20 @@ usb1_drd_sw: endpoint {
};
};
+/* SD */
+&usdhc2 {
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC2>;
+ assigned-clock-rates = <200000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
&iomuxc {
pinctrl_captouch: captouchgrp {
fsl,pins = <
@@ -252,4 +267,46 @@ MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140
MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140
>;
};
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x41
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
index 32f101ef2850..e1d2e2a72e1f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
@@ -295,20 +295,6 @@ brcmf: wifi at 1 {
};
};
-/* SD */
-&usdhc2 {
- assigned-clocks = <&clk IMX8MN_CLK_USDHC2>;
- assigned-clock-rates = <200000000>;
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
- cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
- bus-width = <4>;
- vmmc-supply = <®_usdhc2_vmmc>;
- status = "okay";
-};
-
/* eMMC */
&usdhc3 {
assigned-clocks = <&clk IMX8MN_CLK_USDHC3_ROOT>;
@@ -454,48 +440,6 @@ MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
>;
};
- pinctrl_usdhc2_gpio: usdhc2gpiogrp {
- fsl,pins = <
- MX8MN_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x41
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
- MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
- MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
- MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
- MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
- MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
- MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- >;
- };
-
- pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
- fsl,pins = <
- MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
- MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
- MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
- MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
- MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
- MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
- MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- >;
- };
-
- pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
- fsl,pins = <
- MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
- MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
- MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
- MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
- MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
- MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
- MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- >;
- };
-
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
--
2.47.3
More information about the linux-arm-kernel
mailing list