[PATCH v5 3/3] arm64: dts: rockchip: Add devicetree for the Graperain G3568 v2

[Andrew Lunn]

> +&gmac0 {
> +	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
> +	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>;
> +	assigned-clock-rates = <0>, <125000000>;
> +	clock_in_out = "output";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac0_miim
> +		     &gmac0_tx_bus2
> +		     &gmac0_rx_bus2
> +		     &gmac0_rgmii_clk
> +		     &gmac0_rgmii_bus>;
> +	phy-handle = <&rgmii_phy0>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +};
> +
> +&gmac1 {
> +	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
> +	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
> +	assigned-clock-rates = <0>, <125000000>;
> +	clock_in_out = "output";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac1m1_miim
> +		     &gmac1m1_tx_bus2
> +		     &gmac1m1_rx_bus2
> +		     &gmac1m1_rgmii_clk
> +		     &gmac1m1_rgmii_bus>;
> +	phy-handle = <&rgmii_phy1>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +};

> +&mdio0 {
> +	rgmii_phy0: ethernet-phy at 1 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <1>;
> +		reset-assert-us = <20000>;
> +		reset-deassert-us = <100000>;
> +		reset-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
> +
> +		leds {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			led at 1 {
> +				reg = <1>;
> +				color = <LED_COLOR_ID_GREEN>;
> +				function = LED_FUNCTION_LAN;
> +				default-state = "keep";
> +			};
> +
> +			led at 2 {
> +				reg = <2>;
> +				color = <LED_COLOR_ID_AMBER>;
> +				function = LED_FUNCTION_LAN;
> +				default-state = "keep";
> +			};
> +		};
> +	};
> +};
> +
> +&mdio1 {
> +	rgmii_phy1: ethernet-phy at 1 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <1>;
> +		reset-assert-us = <20000>;
> +		reset-deassert-us = <100000>;
> +		reset-gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_LOW>;
> +
> +		leds {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			led at 1 {
> +				reg = <1>;
> +				color = <LED_COLOR_ID_GREEN>;
> +				function = LED_FUNCTION_LAN;
> +				default-state = "keep";
> +			};
> +
> +			led at 2 {
> +				reg = <2>;
> +				color = <LED_COLOR_ID_AMBER>;
> +				function = LED_FUNCTION_LAN;
> +				default-state = "keep";
> +			};
> +		};
> +	};
> +};

For these nodes only:

Reviewed-by: Andrew Lunn <andrew at lunn.ch>

    Andrew