[PATCH v2 2/2] firmware: arm_scmi: Implement arm,poll-transport property

[Sudeep Holla]

On Mon, Jan 12, 2026 at 12:53:54PM +0000, Cristian Marussi wrote:
> On Mon, Jan 12, 2026 at 12:06:11PM +0000, Sudeep Holla wrote:
> > On Wed, Dec 31, 2025 at 10:29:19PM +0100, Marek Vasut wrote:
> > > Implement new property arm,poll-transport, which sets all SCMI operation into
> > > poll mode. This is meant to work around uncooperative SCP implementations,
> > > which do not generate completion interrupts. This applies to mbox/shmem based
> > > implementations.
> > > 
> > > With this property set, such implementations which do not generate interrupts
> > > can be interacted with, until they are fixed to generate interrupts properly.
> > > 
> > > Signed-off-by: Marek Vasut <marek.vasut+renesas at mailbox.org>
> > > ---
> > > Cc: Conor Dooley <conor+dt at kernel.org>
> > > Cc: Cristian Marussi <cristian.marussi at arm.com>
> > > Cc: Florian Fainelli <florian.fainelli at broadcom.com>
> > > Cc: Krzysztof Kozlowski <krzk+dt at kernel.org>
> > > Cc: Rob Herring <robh at kernel.org>
> > > Cc: Sudeep Holla <sudeep.holla at arm.com>
> > > Cc: arm-scmi at vger.kernel.org
> > > Cc: devicetree at vger.kernel.org
> > > Cc: linux-arm-kernel at lists.infradead.org
> > > Cc: linux-renesas-soc at vger.kernel.org
> > > ---
> > > V2: Drop no IRQ handling from SMC transport and update commit message
> > > ---
> > >  drivers/firmware/arm_scmi/common.h | 4 ++++
> > >  drivers/firmware/arm_scmi/driver.c | 4 ++++
> > >  2 files changed, 8 insertions(+)
> > > 
> > > diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
> > > index 7c35c95fddbaf..7c9617d080a02 100644
> > > --- a/drivers/firmware/arm_scmi/common.h
> > > +++ b/drivers/firmware/arm_scmi/common.h
> > > @@ -235,6 +235,9 @@ struct scmi_transport_ops {
> > >   *		      to have an execution latency lesser-equal to the threshold
> > >   *		      should be considered for atomic mode operation: such
> > >   *		      decision is finally left up to the SCMI drivers.
> > > + * @no_completion_irq: Flag to indicate that this transport has no completion
> > > + *		       interrupt and has to be polled. This is similar to the
> > > + *		       force_polling below, except this is set via DT property.
> > >   * @force_polling: Flag to force this whole transport to use SCMI core polling
> > >   *		   mechanism instead of completion interrupts even if available.
> > >   * @sync_cmds_completed_on_ret: Flag to indicate that the transport assures
> > > @@ -254,6 +257,7 @@ struct scmi_desc {
> > >  	int max_msg;
> > >  	int max_msg_size;
> > >  	unsigned int atomic_threshold;
> > > +	bool no_completion_irq;
> > >  	const bool force_polling;
> > 
> > My preference would be to reuse `force_polling` for this. We need to drop
> > const but that should be OK. Anyways I would like to know if Cristian thinks
> > otherwise for any reasons I might be missing to see.
> 
> I would rather keep the 2 things separate since force_polling is more of
> a brutal low level debug/test facility and, even though it basically
> produces the same result as the new @no_completion_irq, if we remove it
> and unify it in a single boolean that can be overriden from the DT we end
> up in a situation in which we cannot anymore easily force_polling by
> switching the flag in the code since it could be overridden by a
> conflicting 'arm,poll-transport' DT setup. (and you have to patch DT
> for testing)
> 
> So if we have one single underlying boolean (e.g. 'poll') and by any chance
> we end up with a DT containing:
> 
> 	arm,poll-transport = false
> 
> we cannot anymore override the condition by forcing in the code
> 
> 	poll = true,
> 
> since it would be switfly overridden by the DT prop.
> 
> Also semantically force_polling express much more the situation.
> 
> Anyway...I may be overthinking or missing something.
>

Understood, looking at raw I did get a sense of this but didn't spend much
time and thought of asking you. So, all good. Let's not mix them together
then. Thanks for the details!

-- 
Regards,
Sudeep