[PATCH v5 2/2] arm64: dts: ti: Add TQ-Systems TQMa62xx SoM and MBa62xx carrier board Device Trees

[Nishanth Menon]

On 12:21-20260112, Matthias Schiffer wrote:
[...]

> > > +
> > > +	lvds_panel_pins: lvds-panel-pins {
> > > +		pinctrl-single,pins = <
> > > +			/* (N20) GPMC0_BE1n.GPIO0_36 - LVDS0_RESET# */
> > > +			AM62X_IOPAD(0x0094, PIN_OUTPUT, 7)
> > 
> > Could you follow the comment convention you have elsewhere? please follow the
> > same in gpio below etc..
> > AM62X_IOPAD(....) /* (N20) ... */
> 
> I tried to avoid making the lines overly long an adhered to the regular 100
> column limit where reasonable. I agree that the current inconsistent style is
> not so nice... I see two options here:
> 
> - Consistently move the comment to a separate line
> - Break long comments including pin name, pin function and board signal function
>   into two lines
> 

I am not holding 100char limit for pinmux definitions, just pick
a consistent style through out.

[...]

> > > diff --git a/arch/arm64/boot/dts/ti/k3-am625-tqma62xx.dtsi b/arch/arm64/boot/dts/ti/k3-am625-tqma62xx.dtsi
> > > new file mode 100644
> > > index 0000000000000..1b7d58cb7b936
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/ti/k3-am625-tqma62xx.dtsi
> > > @@ -0,0 +1,331 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> > > +/*
> > > + * Copyright (C) 2021-2022 Texas Instruments Incorporated - https://www.ti.com/
> > > + * Copyright (c) 2023-2025 TQ-Systems GmbH <linux at ew.tq-group.com>, D-82229 Seefeld, Germany.
> > > + * Author: Matthias Schiffer
> > > + */
> > 
> > [...]
> > 
> > > +		regulators {
> > > +			reg_buck1: buck1 {
> > > +				regulator-name = "V_VDD_CORE";
> > > +				regulator-min-microvolt = <750000>;
> > > +				regulator-max-microvolt = <750000>;
> > > +				regulator-boot-on;
> > > +				regulator-always-on;
> > > +			};
> > > +
> > [...]
> > 
> > > +
> > > +&a53_opp_table {
> > > +	opp-1400000000 {
> > > +		opp-hz = /bits/ 64 <1400000000>;
> > > +		opp-supported-hw = <0x01 0x0004>;
> > > +		opp-suspend;
> > > +		clock-latency-ns = <6000000>;
> > > +		/* Enabled by bootloader if supported */
> > > +		status = "disabled";
> > 
> > This (bootloader enabling just this node) wont work unless vdd_core
> > voltage is configured to 0.8v as well, no?
> 
> Correct, the bootloader patches both PMIC config and OPP table.

add documentation in regulator node as well, please.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D
https://ti.com/opensource