[EXTERNAL] Re: [PATCH net-next 1/2] net: ti: icssg-prueth: Add Frame Preemption MAC Merge support

[Meghana Malladi]

Hi Vadim,

On 1/7/26 22:02, Vadim Fedorenko wrote:
> On 07/01/2026 12: 51, Meghana Malladi wrote: > This patch adds utility 
> functions to configure firmware to enable > IET FPE. The highest 
> priority queue is marked as Express queue and > lower priority queues as 
> pre-emptable, as the default
> ZjQcmQRYFpfptBannerStart
> This message was sent from outside of Texas Instruments.
> Do not click links or open attachments unless you recognize the source 
> of this email and know the content is safe.
> Report Suspicious
> <https://us-phishalarm-ewt.proofpoint.com/EWT/v1/G3vK! 
> urdgN3dP92274CXOvJKDvwNZ1ZfDoJYHZ2okAgDbtjDN3kmhmKUq71GAYLnzoFwx2mpfBIORw9Qoq3FoueFsPK2L6imycg$>
> ZjQcmQRYFpfptBannerEnd
> 
> On 07/01/2026 12:51, Meghana Malladi wrote:
>> This patch adds utility functions to configure firmware to enable
>> IET FPE. The highest priority queue is marked as Express queue and
>> lower priority queues as pre-emptable, as the default configuration
>> which will be overwritten by the mqprio tc mask passed by tc qdisc.
>> Driver optionally allow configure the Verify state machine in the
>> firmware to check remote peer capability. If remote fails to respond
>> to Verify command, then FPE is disabled by firmware and TX FPE active
>> status is disabled.
>> 
>> This also adds the necessary hooks to enable IET/FPE feature in ICSSG
>> driver. IET/FPE gets configured when Link is up and gets disabled when link
>> goes down or device is stopped.
>> 
>> Signed-off-by: MD Danish Anwar <danishanwar at ti.com>
>> Signed-off-by: Meghana Malladi <m-malladi at ti.com>
>> ---
>>   drivers/net/ethernet/ti/Makefile             |   2 +-
>>   drivers/net/ethernet/ti/icssg/icssg_prueth.c |   9 +
>>   drivers/net/ethernet/ti/icssg/icssg_prueth.h |   2 +
>>   drivers/net/ethernet/ti/icssg/icssg_qos.c    | 319 +++++++++++++++++++
>>   drivers/net/ethernet/ti/icssg/icssg_qos.h    |  48 +++
>>   5 files changed, 379 insertions(+), 1 deletion(-)
>>   create mode 100644 drivers/net/ethernet/ti/icssg/icssg_qos.c
>>   create mode 100644 drivers/net/ethernet/ti/icssg/icssg_qos.h
>> 
>> diff --git a/drivers/net/ethernet/ti/Makefile b/drivers/net/ethernet/ti/Makefile
>> index 93c0a4d0e33a..2f588663fdf0 100644
>> --- a/drivers/net/ethernet/ti/Makefile
>> +++ b/drivers/net/ethernet/ti/Makefile
>> @@ -35,7 +35,7 @@ ti-am65-cpsw-nuss-$(CONFIG_TI_K3_AM65_CPSW_SWITCHDEV) += am65-cpsw-switchdev.o
>>   obj-$(CONFIG_TI_K3_AM65_CPTS) += am65-cpts.o
>>   
>>   obj-$(CONFIG_TI_ICSSG_PRUETH) += icssg-prueth.o icssg.o
>> -icssg-prueth-y := icssg/icssg_prueth.o icssg/icssg_switchdev.o
>> +icssg-prueth-y := icssg/icssg_prueth.o icssg/icssg_switchdev.o icssg/icssg_qos.o
>>   
>>   obj-$(CONFIG_TI_ICSSG_PRUETH_SR1) += icssg-prueth-sr1.o icssg.o
>>   icssg-prueth-sr1-y := icssg/icssg_prueth_sr1.o
>> diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
>> index f65041662173..668177eba3f8 100644
>> --- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
>> +++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
>> @@ -378,6 +378,12 @@ static void emac_adjust_link(struct net_device *ndev)
>>   		} else {
>>   			icssg_set_port_state(emac, ICSSG_EMAC_PORT_DISABLE);
>>   		}
>> +
>> +		if (emac->link) {
>> +			icssg_qos_link_up(ndev);
>> +		} else {
>> +			icssg_qos_link_down(ndev);
>> +		}
> 
> I believe this chunk can be incorporated into if-statement right above
> 

Yeah sure. Will update this as part of v2. Thanks.

>>   	}
>>   
>>   	if (emac->link) {
> 
> [...]
>