[PATCH 5/5] ARM: dts: microchip: sama7d65: add missing flexcom nodes
nicolas.ferre at microchip.com
nicolas.ferre at microchip.com
Fri Jan 2 09:01:34 PST 2026
From: Nicolas Ferre <nicolas.ferre at microchip.com>
Add nodes for usart, spi and i2c when missing to the
flexcom nodes.
Signed-off-by: Nicolas Ferre <nicolas.ferre at microchip.com>
---
arch/arm/boot/dts/microchip/sama7d65.dtsi | 271 ++++++++++++++++++++++
1 file changed, 271 insertions(+)
diff --git a/arch/arm/boot/dts/microchip/sama7d65.dtsi b/arch/arm/boot/dts/microchip/sama7d65.dtsi
index 82781a1dbd6d..e21556f46384 100644
--- a/arch/arm/boot/dts/microchip/sama7d65.dtsi
+++ b/arch/arm/boot/dts/microchip/sama7d65.dtsi
@@ -419,6 +419,21 @@ uart0: serial at 200 {
status = "disabled";
};
+ spi0: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(6)>,
+ <&dma1 AT91_XDMAC_DT_PERID(5)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
i2c0: i2c at 600 {
compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -443,6 +458,22 @@ flx1: flexcom at e1824000 {
#size-cells = <1>;
status = "disabled";
+ uart1: serial at 200 {
+ compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 35>;
+ clock-names = "usart";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+ <&dma0 AT91_XDMAC_DT_PERID(7)>;
+ dma-names = "tx", "rx";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <32>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+ status = "disabled";
+ };
+
spi1: spi at 400 {
compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
@@ -497,6 +528,35 @@ uart2: serial at 200 {
atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
status = "disabled";
};
+
+ spi2: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 36>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(10)>,
+ <&dma1 AT91_XDMAC_DT_PERID(9)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at 600 {
+ compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 36>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(10)>,
+ <&dma1 AT91_XDMAC_DT_PERID(9)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
flx3: flexcom at e182c000 {
@@ -524,6 +584,21 @@ uart3: serial at 200 {
status = "disabled";
};
+ spi3: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>,
+ <&dma0 AT91_XDMAC_DT_PERID(11)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
i2c3: i2c at 600 {
compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -579,6 +654,20 @@ spi4: spi at 400 {
atmel,fifo-size = <32>;
status = "disabled";
};
+
+ i2c4: i2c at 600 {
+ compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(14)>,
+ <&dma1 AT91_XDMAC_DT_PERID(13)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
flx5: flexcom at e201c000 {
@@ -590,6 +679,37 @@ flx5: flexcom at e201c000 {
#size-cells = <1>;
status = "disabled";
+ uart5: serial at 200 {
+ compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+ clock-names = "usart";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(16)>,
+ <&dma0 AT91_XDMAC_DT_PERID(15)>;
+ dma-names = "tx", "rx";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <32>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+ status = "disabled";
+ };
+
+ spi5: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(16)>,
+ <&dma0 AT91_XDMAC_DT_PERID(15)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
i2c5: i2c at 600 {
compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -629,6 +749,35 @@ uart6: serial at 200 {
atmel,fifo-size = <32>;
status = "disabled";
};
+
+ spi6: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(18)>,
+ <&dma1 AT91_XDMAC_DT_PERID(17)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
+ i2c6: i2c at 600 {
+ compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(18)>,
+ <&dma1 AT91_XDMAC_DT_PERID(17)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
flx7: flexcom at e2024000 {
@@ -655,6 +804,35 @@ uart7: serial at 200 {
atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
status = "disabled";
};
+
+ spi7: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>,
+ <&dma1 AT91_XDMAC_DT_PERID(19)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
+ i2c7: i2c at 600 {
+ compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>,
+ <&dma1 AT91_XDMAC_DT_PERID(19)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
flx8: flexcom at e281c000 {
@@ -666,6 +844,37 @@ flx8: flexcom at e281c000 {
#size-cells = <1>;
status = "disabled";
+ uart8: serial at 200 {
+ compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+ clock-names = "usart";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+ <&dma0 AT91_XDMAC_DT_PERID(21)>;
+ dma-names = "tx", "rx";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <32>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+ status = "disabled";
+ };
+
+ spi8: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+ <&dma0 AT91_XDMAC_DT_PERID(21)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
i2c8: i2c at 600 {
compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -690,6 +899,37 @@ flx9: flexcom at e2820000 {
#size-cells = <1>;
status = "disabled";
+ uart9: serial at 200 {
+ compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+ clock-names = "usart";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+ <&dma0 AT91_XDMAC_DT_PERID(23)>;
+ dma-names = "tx", "rx";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <32>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+ status = "disabled";
+ };
+
+ spi9: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+ <&dma0 AT91_XDMAC_DT_PERID(23)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
i2c9: i2c at 600 {
compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -714,6 +954,37 @@ flx10: flexcom at e2824000 {
#size-cells = <1>;
status = "disabled";
+ uart10: serial at 200 {
+ compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+ clock-names = "usart";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(26)>,
+ <&dma0 AT91_XDMAC_DT_PERID(25)>;
+ dma-names = "tx", "rx";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <32>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+ status = "disabled";
+ };
+
+ spi10: spi at 400 {
+ compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(26)>,
+ <&dma0 AT91_XDMAC_DT_PERID(25)>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
i2c10: i2c at 600 {
compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
--
2.43.0
More information about the linux-arm-kernel
mailing list