[PATCH v2 3/3] arm64: dts: imx8dxl: Add SolidRun SoM and HummingBoard

[Vladimir Oltean]

On Thu, Apr 30, 2026 at 11:17:36AM +0000, Josua Mayer wrote:
> Am 09.04.26 um 14:46 schrieb Andrew Lunn:
> >> +&eqos {
> >> +	/* delays are added by connected ethernet-switch cpu port */
> >> +	phy-mode = "rgmii";
> >> +	pinctrl-0 = <&eqos_pins>;
> >> +	pinctrl-names = "default";
> >> +	status = "okay";
> >> +
> >> +	fixed-link {
> >> +		full-duplex;
> >> +		speed = <1000>;
> >> +	};
> >> +};
> >
> >> +	ethernet-switch at 0 {
> >> +		compatible = "nxp,sja1110a";
> >> +		reg = <0>;
> >> +		reset-gpios = <&lsio_gpio4 3 GPIO_ACTIVE_LOW>;
> >> +		spi-max-frequency = <4000000>;
> >> +
> >> +		ethernet-ports {
> >> +			#address-cells = <1>;
> >> +			#size-cells = <0>;
> >> +
> >> +			/* 100Base-TX on connector J26 */
> >> +			port at 1 {
> >> +				reg = <0x1>;
> >> +				label = "lan1";
> >> +				phy-handle = <&switch_port1_base_tx_phy>;
> >> +				phy-mode = "internal";
> >> +				status = "okay";
> dropping unnecessary status okay for v3
> >> +			};
> >> +
> >> +			/* CPU */
> >> +			port at 2 {
> >> +				reg = <0x2>;
> >> +				ethernet = <&eqos>;
> >> +				label = "cpu";

Please drop unused label = "cpu". Also, can you use udev for user
interface naming?

> >> +				phy-mode = "rgmii-id";
> >> +				rx-internal-delay-ps = <2000>;
> >> +				tx-internal-delay-ps = <2000>;
> >> +				status = "okay";
> dropping unnecessary status okay for v3
> >> +
> >> +				fixed-link {
> >> +					full-duplex;
> >> +					speed = <1000>;
> >> +				};
> >> +			};
> >> +
> >> +			/* sgmii on addon board connector J21 */
> >> +			port at 3 {
> >> +				reg = <0x3>;
> >> +				label = "lan3";
> >> +				status = "disabled";
> >> +			};
> >> +
> >> +			/* sgmii on addon board connector J21 */
> >> +			port at 4 {
> >> +				reg = <0x4>;
> >> +				label = "lan4";
> >> +				status = "disabled";
> >> +			};
> >> +
> >> +			/* 100base-t1 on addon board connector J21 */
> >> +			port at 5 {
> >> +				reg = <0x5>;
> >> +				label = "trx1";
> >> +				phy-handle = <&switch_port5_base_t1_phy>;
> >> +				phy-mode = "internal";
> >> +				status = "disabled";
> >> +			};
> >> +
> >> +			/* 100base-t1 on addon board connector J21 */
> >> +			port at 6 {
> >> +				reg = <0x6>;
> >> +				label = "trx2";
> >> +				phy-handle = <&switch_port6_base_t1_phy>;
> >> +				phy-mode = "internal";
> >> +				status = "disabled";
> >> +			};
> >> +
> >> +			/* 100base-t1 on addon board connector J21 */
> >> +			port at 7 {
> >> +				reg = <0x7>;
> >> +				label = "trx3";
> >> +				phy-handle = <&switch_port7_base_t1_phy>;
> >> +				phy-mode = "internal";
> >> +				status = "disabled";
> >> +			};
> >> +
> >> +			/* 100base-t1 on addon board connector J21 */
> >> +			port at 8 {
> >> +				reg = <0x8>;
> >> +				label = "trx4";
> >> +				phy-handle = <&switch_port8_base_t1_phy>;
> >> +				phy-mode = "internal";
> >> +				status = "disabled";
> >> +			};
> >> +
> >> +			/* 100base-t1 on addon board connector J21 */
> >> +			port at 9 {
> >> +				reg = <0x9>;
> >> +				label = "trx5";
> >> +				phy-handle = <&switch_port9_base_t1_phy>;
> >> +				phy-mode = "internal";
> >> +				status = "disabled";
> >> +			};
> >> +
> >> +			/* 100Base-T1 on connector J26 */
> >> +			port at a {
> >> +				reg = <0xa>;
> >> +				label = "trx6";
> >> +				phy-handle = <&switch_port10_base_t1_phy>;
> >> +				phy-mode = "internal";
> >> +				status = "okay";
> dropping unnecessary status okay for v3
> >> +			};
> >> +		};
> >> +
> >> +		mdios {
> >> +			#address-cells = <1>;
> >> +			#size-cells = <0>;
> >> +
> >> +			mdio at 0 {
> >> +				compatible = "nxp,sja1110-base-t1-mdio";
> >> +				reg = <0>;
> >> +				#address-cells = <1>;
> >> +				#size-cells = <0>;
> >> +
> >> +				/* 100base-t1 on addon board connector J21 */
> >> +				switch_port5_base_t1_phy: ethernet-phy at 1 {
> >> +					compatible = "ethernet-phy-ieee802.3-c45";
> >> +					reg = <0x1>;
> >> +					status = "disabled";
> >> +				};
> >> +
> >> +				/* 100base-t1 on addon board connector J21 */
> >> +				switch_port6_base_t1_phy: ethernet-phy at 2 {
> >> +					compatible = "ethernet-phy-ieee802.3-c45";
> >> +					reg = <0x2>;
> >> +					status = "disabled";
> >> +				};
> >> +
> >> +				/* 100base-t1 on addon board connector J21 */
> >> +				switch_port7_base_t1_phy: ethernet-phy at 3 {
> >> +					compatible = "ethernet-phy-ieee802.3-c45";
> >> +					reg = <0x3>;
> >> +					status = "disabled";
> >> +				};
> >> +
> >> +				/* 100base-t1 on addon board connector J21 */
> >> +				switch_port8_base_t1_phy: ethernet-phy at 4 {
> >> +					compatible = "ethernet-phy-ieee802.3-c45";
> >> +					reg = <0x4>;
> >> +					status = "disabled";
> >> +				};
> >> +
> >> +				/* 100base-t1 on addon board connector J21 */
> >> +				switch_port9_base_t1_phy: ethernet-phy at 5 {
> >> +					compatible = "ethernet-phy-ieee802.3-c45";
> >> +					reg = <0x5>;
> >> +					status = "disabled";
> >> +				};
> >> +
> >> +				/* 100Base-T1 on connector J26 */
> >> +				switch_port10_base_t1_phy: ethernet-phy at 6 {
> >> +					compatible = "ethernet-phy-ieee802.3-c45";
> >> +					reg = <0x6>;
> >> +				};
> >> +			};
> >> +
> >> +			mdio at 1 {
> >> +				compatible = "nxp,sja1110-base-tx-mdio";
> >> +				reg = <1>;
> >> +				#address-cells = <1>;
> >> +				#size-cells = <0>;
> >> +
> >> +				/* 100Base-TX on connector J26 */
> >> +				switch_port1_base_tx_phy: ethernet-phy at 1 {
> >> +					reg = <0x1>;
> >> +				};
> >> +			};
> > For these nodes only:
> >
> > Reviewed-by: Andrew Lunn <andrew at lunn.ch>
> >
> >     Andrew
> 
> Thanks!
> 
> I don't know how to keep this partial review for v3, so I will send it without.