[PATCH v2 3/3] arm64: dts: imx8dxl: Add SolidRun SoM and HummingBoard

[Andrew Lunn]

> +&eqos {
> +	/* delays are added by connected ethernet-switch cpu port */
> +	phy-mode = "rgmii";
> +	pinctrl-0 = <&eqos_pins>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	fixed-link {
> +		full-duplex;
> +		speed = <1000>;
> +	};
> +};


> +	ethernet-switch at 0 {
> +		compatible = "nxp,sja1110a";
> +		reg = <0>;
> +		reset-gpios = <&lsio_gpio4 3 GPIO_ACTIVE_LOW>;
> +		spi-max-frequency = <4000000>;
> +
> +		ethernet-ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			/* 100Base-TX on connector J26 */
> +			port at 1 {
> +				reg = <0x1>;
> +				label = "lan1";
> +				phy-handle = <&switch_port1_base_tx_phy>;
> +				phy-mode = "internal";
> +				status = "okay";
> +			};
> +
> +			/* CPU */
> +			port at 2 {
> +				reg = <0x2>;
> +				ethernet = <&eqos>;
> +				label = "cpu";
> +				phy-mode = "rgmii-id";
> +				rx-internal-delay-ps = <2000>;
> +				tx-internal-delay-ps = <2000>;
> +				status = "okay";
> +
> +				fixed-link {
> +					full-duplex;
> +					speed = <1000>;
> +				};
> +			};
> +
> +			/* sgmii on addon board connector J21 */
> +			port at 3 {
> +				reg = <0x3>;
> +				label = "lan3";
> +				status = "disabled";
> +			};
> +
> +			/* sgmii on addon board connector J21 */
> +			port at 4 {
> +				reg = <0x4>;
> +				label = "lan4";
> +				status = "disabled";
> +			};
> +
> +			/* 100base-t1 on addon board connector J21 */
> +			port at 5 {
> +				reg = <0x5>;
> +				label = "trx1";
> +				phy-handle = <&switch_port5_base_t1_phy>;
> +				phy-mode = "internal";
> +				status = "disabled";
> +			};
> +
> +			/* 100base-t1 on addon board connector J21 */
> +			port at 6 {
> +				reg = <0x6>;
> +				label = "trx2";
> +				phy-handle = <&switch_port6_base_t1_phy>;
> +				phy-mode = "internal";
> +				status = "disabled";
> +			};
> +
> +			/* 100base-t1 on addon board connector J21 */
> +			port at 7 {
> +				reg = <0x7>;
> +				label = "trx3";
> +				phy-handle = <&switch_port7_base_t1_phy>;
> +				phy-mode = "internal";
> +				status = "disabled";
> +			};
> +
> +			/* 100base-t1 on addon board connector J21 */
> +			port at 8 {
> +				reg = <0x8>;
> +				label = "trx4";
> +				phy-handle = <&switch_port8_base_t1_phy>;
> +				phy-mode = "internal";
> +				status = "disabled";
> +			};
> +
> +			/* 100base-t1 on addon board connector J21 */
> +			port at 9 {
> +				reg = <0x9>;
> +				label = "trx5";
> +				phy-handle = <&switch_port9_base_t1_phy>;
> +				phy-mode = "internal";
> +				status = "disabled";
> +			};
> +
> +			/* 100Base-T1 on connector J26 */
> +			port at a {
> +				reg = <0xa>;
> +				label = "trx6";
> +				phy-handle = <&switch_port10_base_t1_phy>;
> +				phy-mode = "internal";
> +				status = "okay";
> +			};
> +		};
> +
> +		mdios {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			mdio at 0 {
> +				compatible = "nxp,sja1110-base-t1-mdio";
> +				reg = <0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				/* 100base-t1 on addon board connector J21 */
> +				switch_port5_base_t1_phy: ethernet-phy at 1 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x1>;
> +					status = "disabled";
> +				};
> +
> +				/* 100base-t1 on addon board connector J21 */
> +				switch_port6_base_t1_phy: ethernet-phy at 2 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x2>;
> +					status = "disabled";
> +				};
> +
> +				/* 100base-t1 on addon board connector J21 */
> +				switch_port7_base_t1_phy: ethernet-phy at 3 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x3>;
> +					status = "disabled";
> +				};
> +
> +				/* 100base-t1 on addon board connector J21 */
> +				switch_port8_base_t1_phy: ethernet-phy at 4 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x4>;
> +					status = "disabled";
> +				};
> +
> +				/* 100base-t1 on addon board connector J21 */
> +				switch_port9_base_t1_phy: ethernet-phy at 5 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x5>;
> +					status = "disabled";
> +				};
> +
> +				/* 100Base-T1 on connector J26 */
> +				switch_port10_base_t1_phy: ethernet-phy at 6 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x6>;
> +				};
> +			};
> +
> +			mdio at 1 {
> +				compatible = "nxp,sja1110-base-tx-mdio";
> +				reg = <1>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				/* 100Base-TX on connector J26 */
> +				switch_port1_base_tx_phy: ethernet-phy at 1 {
> +					reg = <0x1>;
> +				};
> +			};

For these nodes only:

Reviewed-by: Andrew Lunn <andrew at lunn.ch>

    Andrew