[PATCH 1/2] dt-bindings: reset: imx8mq: Add _N suffix to IMX8MQ_RESET_MIPI_CSI*_RESET

[Krzysztof Kozlowski]

On Tue, Mar 31, 2026 at 06:13:30PM +0800, Robby Cai wrote:
> The assert logic of the MIPI CSI reset signals is active-low on i.MX8MQ,
> but the existing names do not indicate this explicitly. To improve
> consistency and clarity, append the _N suffix to all
> IMX8MQ_RESET_MIPI_CSI*_RESET definitions. The deprecated
> IMX8MQ_RESET_MIPI_CSI*_RESET versions remain temporarily for DT ABI
> compatibility and will be removed at an appropriate time in the future.
> 
> Signed-off-by: Robby Cai <robby.cai at nxp.com>
> ---
>  include/dt-bindings/reset/imx8mq-reset.h | 18 ++++++++++++------
>  1 file changed, 12 insertions(+), 6 deletions(-)
> 
> diff --git a/include/dt-bindings/reset/imx8mq-reset.h b/include/dt-bindings/reset/imx8mq-reset.h
> index 705870693ec2..83a155dbbd4a 100644
> --- a/include/dt-bindings/reset/imx8mq-reset.h
> +++ b/include/dt-bindings/reset/imx8mq-reset.h
> @@ -46,12 +46,18 @@
>  #define IMX8MQ_RESET_PCIEPHY2_PERST		35	/* i.MX8MM/i.MX8MN does NOT support */
>  #define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN		36	/* i.MX8MM/i.MX8MN does NOT support */
>  #define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF	37	/* i.MX8MM/i.MX8MN does NOT support */
> -#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET	38	/* i.MX8MM/i.MX8MN does NOT support */
> -#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET	39	/* i.MX8MM/i.MX8MN does NOT support */
> -#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET	40	/* i.MX8MM/i.MX8MN does NOT support */
> -#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET	41	/* i.MX8MM/i.MX8MN does NOT support */
> -#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET	42	/* i.MX8MM/i.MX8MN does NOT support */
> -#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET	43	/* i.MX8MM/i.MX8MN does NOT support */
> +#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET	38	/* Deprecated. Use *_RESET_N instead */
> +#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET_N	38	/* i.MX8MM/i.MX8MN does NOT support */

That's quite a churn for no need. The entire point of these values being
the binding is that it describes the ABI for SW and DTS, not your
hardware registers.

Whether signal is active low or high is kind of irrelevant. Linux uses
it exactly the same way.

Best regards,
Krzysztof