[PATCH] dt-bindings: mmc: socionext,milbeaut-m10v-sdhci-3.0: convert to DT schema

[Charan Pedumuru]

On 27-10-2025 19:27, Rob Herring wrote:
> On Thu, Oct 23, 2025 at 05:37:36PM +0000, Charan Pedumuru wrote:
>> Convert SOCIONEXT Milbeaut SDHCI controller binding to YAML format.
>> Add a new property "voltage-ranges" to resolve dt_check errors.
>>
>> Signed-off-by: Charan Pedumuru <charan.pedumuru at gmail.com>
>> ---
>>  .../devicetree/bindings/mmc/sdhci-milbeaut.txt     | 30 ---------
>>  .../mmc/socionext,milbeaut-m10v-sdhci-3.0.yaml     | 78 ++++++++++++++++++++++
>>  2 files changed, 78 insertions(+), 30 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt b/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt
>> deleted file mode 100644
>> index 627ee89c125b..000000000000
>> --- a/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt
>> +++ /dev/null
>> @@ -1,30 +0,0 @@
>> -* SOCIONEXT Milbeaut SDHCI controller
>> -
>> -This file documents differences between the core properties in mmc.txt
>> -and the properties used by the sdhci_milbeaut driver.
>> -
>> -Required properties:
>> -- compatible: "socionext,milbeaut-m10v-sdhci-3.0"
>> -- clocks: Must contain an entry for each entry in clock-names. It is a
>> -  list of phandles and clock-specifier pairs.
>> -  See ../clocks/clock-bindings.txt for details.
>> -- clock-names: Should contain the following two entries:
>> -	"iface" - clock used for sdhci interface
>> -	"core"  - core clock for sdhci controller
>> -
>> -Optional properties:
>> -- fujitsu,cmd-dat-delay-select: boolean property indicating that this host
>> -  requires the CMD_DAT_DELAY control to be enabled.
>> -
>> -Example:
>> -	sdhci3: mmc at 1b010000 {
>> -		compatible = "socionext,milbeaut-m10v-sdhci-3.0";
>> -		reg = <0x1b010000 0x10000>;
>> -		interrupts = <0 265 0x4>;
>> -		voltage-ranges = <3300 3300>;
>> -		bus-width = <4>;
>> -		clocks = <&clk 7>, <&ahb_clk>;
>> -		clock-names = "core", "iface";
>> -		cap-sdio-irq;
>> -		fujitsu,cmd-dat-delay-select;
>> -	};
>> diff --git a/Documentation/devicetree/bindings/mmc/socionext,milbeaut-m10v-sdhci-3.0.yaml b/Documentation/devicetree/bindings/mmc/socionext,milbeaut-m10v-sdhci-3.0.yaml
>> new file mode 100644
>> index 000000000000..6b67bef30347
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mmc/socionext,milbeaut-m10v-sdhci-3.0.yaml
>> @@ -0,0 +1,78 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mmc/socionext,milbeaut-m10v-sdhci-3.0.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: SOCIONEXT Milbeaut SDHCI controller
>> +
>> +maintainers:
>> +  - Taichi Sugaya <sugaya.taichi at socionext.com>
>> +  - Takao Orito <orito.takao at socionext.com>
>> +
>> +description:
>> +  The SOCIONEXT Milbeaut SDHCI controller is a specialized SD Host
>> +  Controller found in some of Socionext's Milbeaut image processing SoCs.
>> +  It features a dedicated "bridge controller." This bridge controller
>> +  implements special functions like reset control, clock management for
>> +  various SDR modes (SDR12, SDR25, SDR50) and physical pin property settings.
>> +
>> +allOf:
>> +  - $ref: sdhci-common.yaml#
>> +
>> +properties:
>> +  compatible:
>> +    const: socionext,milbeaut-m10v-sdhci-3.0
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 2
>> +
>> +  clock-names:
>> +    items:
>> +      - const: core
>> +      - const: iface
>> +
>> +  fujitsu,cmd-dat-delay-select:
>> +    description:
>> +      Its presence indicates that the controller requires a specific command
>> +      and data line delay selection mechanism for proper operation, particularly
>> +      when dealing with high-speed SD/eMMC modes.
>> +    type: boolean
>> +
>> +  voltage-ranges:
>> +    $ref: /schemas/types.yaml#/definitions/uint32-matrix
> 
> Sounds more like a uint32-array.

Okay, I will change that.

> 
>> +    description:
>> +      Two cells are required, first cell specifies minimum slot voltage (mV),
>> +      second cell specifies maximum slot voltage (mV).
>> +    maxItems: 1
> 
> You can better describe it like this:
> 
> items:
>   - description: minimum slot voltage (mV)
>   - description: maximum slot voltage (mV)

Sure.

-- 
Best Regards,
Charan.