[PATCH v7 5/5] arm64: dts: imx8ulp: Add CSI and ISI Nodes

[Laurent Pinchart]

On Thu, Oct 23, 2025 at 05:19:46PM +0800, Guoniu Zhou wrote:
> From: Guoniu Zhou <guoniu.zhou at nxp.com>
> 
> The CSI-2 in the i.MX8ULP is almost identical to the version present
> in the i.MX8QXP/QM and is routed to the ISI. Add both the ISI and CSI
> nodes and mark them as disabled by default since capture is dependent
> on an attached camera.
> 
> Reviewed-by: Frank Li <Frank.Li at nxp.com>
> Signed-off-by: Guoniu Zhou <guoniu.zhou at nxp.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>

> ---
>  arch/arm64/boot/dts/freescale/imx8ulp.dtsi | 67 ++++++++++++++++++++++++++++++
>  1 file changed, 67 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
> index 13b01f3aa2a4950c37e72e04f6bfb5995dc19178..99271d55dfb60ed2cbfe664d928be179eb257674 100644
> --- a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
> @@ -7,6 +7,7 @@
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/power/imx8ulp-power.h>
> +#include <dt-bindings/reset/imx8ulp-pcc-reset.h>
>  #include <dt-bindings/thermal/thermal.h>
>  
>  #include "imx8ulp-pinfunc.h"
> @@ -842,6 +843,72 @@ spdif: spdif at 2dab0000 {
>  				dma-names = "rx", "tx";
>  				status = "disabled";
>  			};
> +
> +			isi: isi at 2dac0000 {
> +				compatible = "fsl,imx8ulp-isi";
> +				reg = <0x2dac0000 0x10000>;
> +				interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&pcc5 IMX8ULP_CLK_ISI>,
> +					 <&cgc2 IMX8ULP_CLK_LPAV_AXI_DIV>;
> +				clock-names = "axi", "apb";
> +				power-domains = <&scmi_devpd IMX8ULP_PD_ISI>;
> +				status = "disabled";
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;
> +						isi_in: endpoint {
> +							remote-endpoint = <&mipi_csi_out>;
> +						};
> +					};
> +				};
> +			};
> +
> +			mipi_csi: csi at 2daf0000 {
> +				compatible = "fsl,imx8ulp-mipi-csi2";
> +				reg = <0x2daf0000 0x10000>,
> +				      <0x2dad0000 0x10000>;
> +				clocks = <&pcc5 IMX8ULP_CLK_CSI>,
> +					 <&pcc5 IMX8ULP_CLK_CSI_CLK_ESC>,
> +					 <&pcc5 IMX8ULP_CLK_CSI_CLK_UI>,
> +					 <&pcc5 IMX8ULP_CLK_CSI_REGS>;
> +				clock-names = "core", "esc", "ui", "pclk";
> +				assigned-clocks = <&pcc5 IMX8ULP_CLK_CSI>,
> +						  <&pcc5 IMX8ULP_CLK_CSI_CLK_ESC>,
> +						  <&pcc5 IMX8ULP_CLK_CSI_CLK_UI>,
> +						  <&pcc5 IMX8ULP_CLK_CSI_REGS>;
> +				assigned-clock-parents = <&cgc2 IMX8ULP_CLK_PLL4_PFD1_DIV1>,
> +							 <&cgc2 IMX8ULP_CLK_PLL4_PFD1_DIV2>,
> +							 <&cgc2 IMX8ULP_CLK_PLL4_PFD0_DIV1>;
> +				assigned-clock-rates = <200000000>,
> +						       <80000000>,
> +						       <100000000>,
> +						       <79200000>;
> +				power-domains = <&scmi_devpd IMX8ULP_PD_MIPI_CSI>;
> +				resets = <&pcc5 PCC5_CSI_SWRST>,
> +					 <&pcc5 PCC5_CSI_REGS_SWRST>;
> +				status = "disabled";
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;
> +					};
> +
> +					port at 1 {
> +						reg = <1>;
> +
> +						mipi_csi_out: endpoint {
> +							remote-endpoint = <&isi_in>;
> +						};
> +					};
> +				};
> +			};
>  		};
>  
>  		gpiod: gpio at 2e200000 {

-- 
Regards,

Laurent Pinchart