[PATCH v11 05/11] dt-bindings: phy: rockchip: rk3399-typec-phy: Support mode-switch

[Rob Herring (Arm)]

On Fri, 28 Nov 2025 10:03:59 +0800, Chaoyi Chen wrote:
> From: Chaoyi Chen <chaoyi.chen at rock-chips.com>
> 
> The RK3399 SoC integrates two USB/DP combo PHYs, each of which
> supports software-configurable pin mapping and DisplayPort lane
> assignment. These capabilities enable the PHY itself to handle both
> mode switching and orientation switching, based on the Type-C plug
> orientation and USB PD negotiation results.
> 
> While an external Type-C controller is still required to detect cable
> attachment and report USB PD events, the actual mode and orientation
> switching is performed internally by the PHY through software
> configuration. This allows the PHY to act as a Type-C multiplexer for
> both data role and DP altmode configuration.
> 
> To reflect this hardware design, this patch introduces a new
> "mode-switch" property for the dp-port node in the device tree bindings.
> This property indicates that the connected PHY is capable of handling
> Type-C mode switching itself.
> 
> Signed-off-by: Chaoyi Chen <chaoyi.chen at rock-chips.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
> ---
> 
> (no changes since v5)
> 
> Changes in v4:
> - Remove "|" in description.
> 
> Changes in v3:
> - Add more descriptions to clarify the role of the PHY in switching.
> 
> Changes in v2:
> - Reuse dp-port/usb3-port in rk3399-typec-phy binding.
> 
>  .../devicetree/bindings/phy/rockchip,rk3399-typec-phy.yaml  | 6 ++++++
>  1 file changed, 6 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): 'audio-codec at 1,0' does not match any of the regexes: '^pinctrl-[0-9]+$', '^slim@[0-9a-f]+$'
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): #address-cells: 1 was expected
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): 'dmas' is a required property
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): 'dma-names' is a required property
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20251128020405.90-6-kernel@airkyi.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.