[PATCH 2/2] arm64: dts: rockchip: add Tinkerboard 3 and 3S device tree

[Heiko Stübner]

Hi Michael,

Am Dienstag, 11. November 2025, 18:20:23 Mitteleuropäische Normalzeit schrieb michael.opdenacker at rootcommit.com:
> From: Michael Opdenacker <michael.opdenacker at rootcommit.com>
> 
> Add initial device tree support for Asus Tinkerboard 3 [1] and 3S [2],
> which are SBCs based on the Rockchip 3566 SoC.
> 
> The "3S" version ("S" for "storage") just adds a 16 GB eMMC
> and a "mask ROM" DIP switch (to mask the eMMC and enter "Mask ROM"
> mode for recovery) to the "3" version.
> 
> This adds support for:
> - Debug UART (/dev/ttyS2)
> - SD card (/dev/mmcblk1)
> - eMMC (/dev/mmcblk0, only on Tinkerboard 3S)
> - I2C:
>   - i2c0 (internal bus with a PMIC and regulators)
>   - i2c2 (internal bus with an at24 eeprom and an RTC device)
> - USB 2.0 ports
> - 2 GPIO LEDS
> 
> Link: https://tinker-board.asus.com/series/tinker-board-3.html [1]
> Link: https://tinker-board.asus.com/series/tinker-board-3s.html [2]
> Signed-off-by: Michael Opdenacker <michael.opdenacker at rootcommit.com>
> ---

please follow the DTS coding style
https://docs.kernel.org/devicetree/bindings/dts-coding-style.html


> +/ {
> +	aliases {
> +		serial2 = &uart2;
> +		mmc1 = &sdmmc0;
> +		i2c0 = &i2c0;
> +		i2c2 = &i2c2;

alphabetical property order


> +	};
> +
> +	chosen {
> +		stdout-path = "serial2:1500000n8";
> +	};
> +
> +	vcc3v3_sys: regulator-3v3-vcc-sys {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc5v0_sys: regulator-5v0-vcc-sys {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vcc5v0_usb_host: regulator-5v0-vcc-usb-host {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_host_pwren_h>;
> +		regulator-name = "vcc5v0_usb_host";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	gpio_leds: gpio-leds {

gpio-foo before regulator-bar

> +		compatible = "gpio-leds";
> +
> +		act-led {
> +			gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger="mmc1";
> +};

missing indentation

> +
> +		rsv-led {
> +			gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger="none";
> +		};
> +	};
> +};
> +
> +&uart2 {

alphabetical ordering of phandles please (uart2 definitly somewhere after i2c0)

> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	rk809: pmic at 20 {
> +		compatible = "rockchip,rk809";
> +		reg = <0x20>;
> +		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> +		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> +		#clock-cells = <1>;
> +		clocks = <&cru I2S1_MCLKOUT_TX>;
> +		clock-names = "mclk";
> +		clock-output-names = "rk809-clkout1", "rk809-clkout2";
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
> +		#sound-dai-cells = <0>;
> +		system-power-controller;
> +		wakeup-source;
> +
> +		vcc1-supply = <&vcc3v3_sys>;
> +		vcc2-supply = <&vcc3v3_sys>;
> +		vcc3-supply = <&vcc3v3_sys>;
> +		vcc4-supply = <&vcc3v3_sys>;
> +		vcc5-supply = <&vcc3v3_sys>;
> +		vcc6-supply = <&vcc3v3_sys>;
> +		vcc7-supply = <&vcc3v3_sys>;
> +		vcc8-supply = <&vcc3v3_sys>;
> +		vcc9-supply = <&vcc3v3_sys>;
> +
> +		regulators {
> +			vcc_1v8: DCDC_REG5 {
> +				regulator-name = "vcc_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_sd: SWITCH_REG2 {
> +				regulator-name = "vcc3v3_sd";
> +				regulator-always-on;
> +				regulator-boot-on;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vccio_sd: LDO_REG5 {
> +				regulator-name = "vccio_sd";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_3v3: SWITCH_REG1 {
> +				regulator-name = "vcc_3v3";
> +				regulator-always-on;
> +				regulator-boot-on;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +		};
> +	};
> +
> +	vdd_cpu: regulator at 40 {

you probably need &cpu0 phandles to set this regulator-supply?

> +		compatible = "silergy,syr827";
> +		reg = <0x40>;
> +		fcs,suspend-voltage-selector = <1>;
> +		regulator-name = "vdd_cpu";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <830000>;
> +		regulator-max-microvolt = <1200000>;
> +		regulator-ramp-delay = <2300>;
> +		vin-supply = <&vcc3v3_sys>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +
> +	m24c08 at 50 {

I guess eeprom at 50 ?

Heiko