[PATCH 3/3] ARM: dts: imx: move nand related property under nand at 0

[Francesco Dolcini]

Hello Frank,

On Wed, Nov 05, 2025 at 10:29:05AM -0500, Frank Li wrote:
> On Wed, Nov 05, 2025 at 12:55:38PM +0100, Francesco Dolcini wrote:
> > On Tue, Nov 04, 2025 at 05:27:14PM -0500, Frank Li wrote:
> > > Add child node nand at 0 and move NAND related property under it to align
> > > modern nand-controller.yaml.
> > >
> > > Fix below CHECK_DTBS warnings:
> > >   arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dtb: nand-controller at 1806000 (fsl,imx6q-gpmi-nand): Unevaluated properties are not allowed ('nand-ecc-mode', 'nand-ecc-step-size', 'nand-ecc-strength', 'nand-on-flash-bbt' were unexpected)
> > >         from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
> > >
> > > Since 2019 year, commit
> > > (212e496935929 dt-bindings: mtd: Add YAML schemas for the generic NAND options)
> > > NAND related property is preferred located under nand@<n> even though only
> > > one NAND chip supported.
> > >
> > > Signed-off-by: Frank Li <Frank.Li at nxp.com>
> > > ---
> > >  arch/arm/boot/dts/nxp/imx/imx6-logicpd-som.dtsi           |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi              |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pfla02.dtsi      |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-phycore-som.dtsi |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi           |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6qdl-tx6.dtsi                |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts                 |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi               |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6ul-phytec-phycore-som.dtsi  |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi               |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6ull-colibri.dtsi            | 12 ++++++++----
> > >  arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea.dtsi   | 12 ++++++++----
> > >  arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx.dtsi      |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts          |  6 +++++-
> > >  arch/arm/boot/dts/nxp/imx/imx7-colibri.dtsi               |  8 ++++++--
> > >  15 files changed, 82 insertions(+), 22 deletions(-)
> > >
> >
> > Was any of these changes tested? Is the driver able to cope with the
> > binding change?
> 
> I have not board to do direct test. This format is used at imx8 platform,
> which use the same gpmi driver.
> 
> This properties are parsed at mtd common part
> drivers/mtd/nand/raw/nand_base.c
> 
> If you have one of above board to test it, it will be appericated.

I did a minimal boot test, on colibri-imx6ull, and the board was booting
fine, with Linux 6.18.0-rc4 and this patch applied.

I am wondering if there is any impact with the bootloader, this DT is
used as it is also in U-Boot, and there the NAND driver is for sure
different. Any comment on this? I was not able to test this combination.

Francesco