[PATCH net-next 0/3] net: stmmac: phylink PCS conversion part 3 (dodgy stuff)

[Mohd Ayaan Anwar]

On Mon, Nov 03, 2025 at 11:43:23AM +0000, Russell King (Oracle) wrote:
> On Mon, Nov 03, 2025 at 04:50:03PM +0530, Mohd Ayaan Anwar wrote:
> > On Mon, Nov 03, 2025 at 12:48:20PM +0200, Vladimir Oltean wrote:
> > > 
> > > As Russell partially pointed out, there are several assumptions in the
> > > Aquantia PHY driver and in phylink, three of them being that:
> > > - rate matching is only supported for PHY_INTERFACE_MODE_10GBASER and
> > >   PHY_INTERFACE_MODE_2500BASEX (thus not PHY_INTERFACE_MODE_SGMII)
> > > - if phy_get_rate_matching() returns RATE_MATCH_NONE for an interface,
> > >   pl->phy_state.rate_matching will also be RATE_MATCH_NONE when using
> > >   that interface
> > > - if rate matching is used, the PHY is configured to use it for all
> > >   media speeds <= phylink_interface_max_speed(link_state.interface)
> > > 
> > > Those assumptions are not validated very well against the ground truth
> > > from the PHY provisioning, so the next step would be for us to see that
> > > directly.
> > > 
> > > Please turn this print from aqr_gen2_read_global_syscfg() into something
> > > visible in dmesg, i.e. by replacing phydev_dbg() with phydev_info():
> > > 
> > > 		phydev_dbg(phydev,
> > > 			   "Media speed %d uses host interface %s with %s\n",
> > > 			   syscfg->speed, phy_modes(syscfg->interface),
> > > 			   syscfg->rate_adapt == AQR_RATE_ADAPT_NONE ? "no rate adaptation" :
> > > 			   syscfg->rate_adapt == AQR_RATE_ADAPT_PAUSE ? "rate adaptation through flow control" :
> > > 			   syscfg->rate_adapt == AQR_RATE_ADAPT_USX ? "rate adaptation through symbol replication" :
> > > 			   "unrecognized rate adaptation type");
> > 
> > Thanks. Looks like rate adaptation is only provisioned for 10M, which
> > matches my observation where phylink passes the exact speeds for
> > 100/1000/2500 but 1000 for 10M.
> 
> Hmm, I wonder what the PHY is doing for that then. stmmac will be
> programmed to read the Cisco SGMII in-band control word, and use
> that to determine whether symbol replication for slower speeds is
> being used.
> 
> If AQR115C is indicating 10M in the in-band control word, but is
> actually operating the link at 1G speed, things are not going to
> work, and I would say the PHY is broken to be doing that. The point
> of the SGMII in-band control word is to tell the MAC about the
> required symbol replication on the link for transmitting the slower
> data rates over the link.
> 
> stmmac unfortunately doesn't give access to the raw Cisco SGMII
> in-band control word. However, reading register 0xf8 bits 31:16 for
> dwmac4, or register 0xd8 bits 15:0 for dwmac1000 will give this
> information. In that bitfield, bits 2:1 give the speed. 2 = 1G,
> 1 = 100M, 0 = 10M.
> 

This is dwmac4 and I got the following values with devmem at different
link speeds:
1. 10M:		0x00080000  => Bit 2:1 = 0
2. 100M:	0x000A0000  => Bit 2:1 = 1
3. 1G: 		0x000D0000  => Bit 2:1 = 2

> -- 
> RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
> FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!