[PATCH v2 1/1] Revert "ARM: dts: Update pcie ranges for dra7"

[Frank Li]

On Fri, Apr 11, 2025 at 11:34:54AM -0400, Frank Li wrote:
> This reverts commit c761028ef5e27f477fe14d2b134164c584fc21ee.
>
> The commit being reverted updated the "ranges" property for the sake of
> readability. However, this change is no longer appropriate due to the
> following reasons:
>
> - On many SoCs, the PCIe parent bus translates CPU addresses to different
> values before passing them to the PCIe controller.
> - The reverted commit introduced a fake address translation, which violates
> the fundamental DTS principle: the device tree should reflect actual
> hardware behavior.
>
> Reverting this change prepares for the cleanup of the driver's
> cpu_addr_fixup() hook.
>
> Signed-off-by: Frank Li <Frank.Li at nxp.com>
> ---

s-vadapalli:

	Any update about this patch? it prepare to remove cpu_addr_fixes()!

Frank


> Change from v1 to v2:
> - update commit message to add more detail.
>
> Previous disscusion at
> https://lore.kernel.org/linux-pci/20250314064642.fyf3jqylmc6meft7@uda0492258/
> ---
>  arch/arm/boot/dts/ti/omap/dra7.dtsi | 29 +++++++++++------------------
>  1 file changed, 11 insertions(+), 18 deletions(-)
>
> diff --git a/arch/arm/boot/dts/ti/omap/dra7.dtsi b/arch/arm/boot/dts/ti/omap/dra7.dtsi
> index b709703f6c0d4..711ce4c31bb1f 100644
> --- a/arch/arm/boot/dts/ti/omap/dra7.dtsi
> +++ b/arch/arm/boot/dts/ti/omap/dra7.dtsi
> @@ -195,24 +195,22 @@ axi0: target-module at 51000000 {
>  			clock-names = "fck", "phy-clk", "phy-clk-div";
>  			#size-cells = <1>;
>  			#address-cells = <1>;
> -			ranges = <0x51000000 0x51000000 0x3000>,
> -				 <0x20000000 0x20000000 0x10000000>;
> +			ranges = <0x51000000 0x51000000 0x3000
> +				  0x0	     0x20000000 0x10000000>;
>  			dma-ranges;
>  			/**
>  			 * To enable PCI endpoint mode, disable the pcie1_rc
>  			 * node and enable pcie1_ep mode.
>  			 */
>  			pcie1_rc: pcie at 51000000 {
> -				reg = <0x51000000 0x2000>,
> -				      <0x51002000 0x14c>,
> -				      <0x20001000 0x2000>;
> +				reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>;
>  				reg-names = "rc_dbics", "ti_conf", "config";
>  				interrupts = <0 232 0x4>, <0 233 0x4>;
>  				#address-cells = <3>;
>  				#size-cells = <2>;
>  				device_type = "pci";
> -				ranges = <0x81000000 0 0x00000000 0x20003000 0 0x00010000>,
> -					 <0x82000000 0 0x20013000 0x20013000 0 0x0ffed000>;
> +				ranges = <0x81000000 0 0          0x03000 0 0x00010000
> +					  0x82000000 0 0x20013000 0x13000 0 0xffed000>;
>  				bus-range = <0x00 0xff>;
>  				#interrupt-cells = <1>;
>  				num-lanes = <1>;
> @@ -235,10 +233,7 @@ pcie1_intc: interrupt-controller {
>  			};
>
>  			pcie1_ep: pcie_ep at 51000000 {
> -				reg = <0x51000000 0x28>,
> -				      <0x51002000 0x14c>,
> -				      <0x51001000 0x28>,
> -				      <0x20001000 0x10000000>;
> +				reg = <0x51000000 0x28>, <0x51002000 0x14c>, <0x51001000 0x28>, <0x1000 0x10000000>;
>  				reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
>  				interrupts = <0 232 0x4>;
>  				num-lanes = <1>;
> @@ -269,21 +264,19 @@ axi1: target-module at 51800000 {
>  			reset-names = "rstctrl";
>  			#size-cells = <1>;
>  			#address-cells = <1>;
> -			ranges = <0x51800000 0x51800000 0x3000>,
> -				 <0x30000000 0x30000000 0x10000000>;
> +			ranges = <0x51800000 0x51800000 0x3000
> +				  0x0	     0x30000000 0x10000000>;
>  			dma-ranges;
>  			status = "disabled";
>  			pcie2_rc: pcie at 51800000 {
> -				reg = <0x51800000 0x2000>,
> -				      <0x51802000 0x14c>,
> -				      <0x30001000 0x2000>;
> +				reg = <0x51800000 0x2000>, <0x51802000 0x14c>, <0x1000 0x2000>;
>  				reg-names = "rc_dbics", "ti_conf", "config";
>  				interrupts = <0 355 0x4>, <0 356 0x4>;
>  				#address-cells = <3>;
>  				#size-cells = <2>;
>  				device_type = "pci";
> -				ranges = <0x81000000 0 0x00000000 0x30003000 0 0x00010000>,
> -					 <0x82000000 0 0x30013000 0x30013000 0 0x0ffed000>;
> +				ranges = <0x81000000 0 0          0x03000 0 0x00010000
> +					  0x82000000 0 0x30013000 0x13000 0 0xffed000>;
>  				bus-range = <0x00 0xff>;
>  				#interrupt-cells = <1>;
>  				num-lanes = <1>;
> --
> 2.34.1
>