[PATCH 6/7] arm64: dts: ti: k3-am62a7-sk: Set wakeup-source system-states

[Kendall Willis]

On 4/21/25 03:14, Markus Schneider-Pargmann wrote:
> The CANUART pins of mcu_mcan0, mcu_mcan1, mcu_uart0 and wkup_uart0 are
> powered during Partial-IO and IO+DDR and are capable of waking up the
> system in these states. Specify the states in which these units can do a
> wakeup on this board.
> 
> Note that the UARTs are not capable of wakeup in Partial-IO because of
> of a UART mux on the board not being powered during Partial-IO.
> 
> Add pincontrol definitions for mcu_mcan0 and mcu_mcan1 for wakeup from
> Partial-IO. Add these as wakeup pinctrl entries for both devices.
> 
> Signed-off-by: Markus Schneider-Pargmann <msp at baylibre.com>
> ---
>   arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 76 +++++++++++++++++++++++++++++++++
>   1 file changed, 76 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index 1c9d95696c839a51b607839abb9429a8de6fa620..724d9a6f3c575fe35496fdd9e17d6d8e33869f92 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -741,3 +741,79 @@ dpi1_out: endpoint {
>   		};
>   	};
>   };
> +
> +&mcu_mcan0 {
> +	pinctrl-names = "default", "wakeup";
> +	pinctrl-0 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_default>;
> +	pinctrl-1 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_wakeup>;
> +	wakeup-source = <&system_partial_io>,
> +			<&system_io_ddr>,
> +			<&system_deep_sleep>,
> +			<&system_mcu_only>,
> +			<&system_standby>;
> +	status = "okay";
> +};
> +
> +&mcu_mcan1 {
> +	pinctrl-names = "default", "wakeup";
> +	pinctrl-0 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_default>;
> +	pinctrl-1 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_wakeup>;
> +	wakeup-source = <&system_partial_io>,
> +			<&system_io_ddr>,
> +			<&system_deep_sleep>,
> +			<&system_mcu_only>,
> +			<&system_standby>;
> +	status = "okay";
> +};
> +
> +&mcu_uart0 {
> +	wakeup-source = <&system_io_ddr>,
> +			<&system_deep_sleep>,
> +			<&system_mcu_only>,
> +			<&system_standby>;
> +};
> +
> +&wkup_uart0 {
> +	wakeup-source = <&system_io_ddr>,
> +			<&system_deep_sleep>,
> +			<&system_mcu_only>,
> +			<&system_standby>;
> +};
Hi Markus,

I noticed wkup_uart0 is already referenced earlier in the dts. Could the 
wakeup-source property be added into the first reference?
> +
> +&mcu_pmx0 {
Same thing with mcu_pmx0. Is there a reason for separating it from when 
it was referenced originally?
> +	mcu_mcan0_tx_pins_default: mcu-mcan0-tx-default-pins {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x034, PIN_OUTPUT, 0) /* (D6) MCU_MCAN0_TX */
> +		>;
> +	};
> +
> +	mcu_mcan0_rx_pins_default: mcu-mcan0-rx-default-pins {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x038, PIN_INPUT, 0) /* (B3) MCU_MCAN0_RX */
> +		>;
> +	};
> +
> +	mcu_mcan0_rx_pins_wakeup: mcu-mcan0-rx-wakeup-pins {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x038, PIN_INPUT | WKUP_EN, 0) /* (B3) MCU_MCAN0_RX */
> +		>;
> +	};
> +
> +	mcu_mcan1_tx_pins_default: mcu-mcan1-tx-default-pins {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x03c, PIN_OUTPUT, 0) /* (E5) MCU_MCAN1_TX */
> +		>;
> +	};
> +
> +	mcu_mcan1_rx_pins_default: mcu-mcan1-rx-default-pins {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x040, PIN_INPUT, 0) /* (D4) MCU_MCAN1_RX */
> +		>;
> +	};
> +
> +	mcu_mcan1_rx_pins_wakeup: mcu-mcan1-rx-wakeup-pins {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x040, PIN_INPUT | WKUP_EN, 0) /* (D4) MCU_MCAN1_RX */
> +		>;
> +	};
> +};Additionally, this patch does not apply cleanly to linux-next and needs 
to be fixed and rebased.

Best,
Kendall Willis
>