[PATCH v2 3/3] arm64: dts: rockchip: Add Luckfox Omni3576 Board support

[John Clark]

On 5/4/25 10:12 AM, Andrew Lunn wrote:
>>> +&gmac0 {
>>> +	clock_in_out = "output";
>>> +	phy-handle = <&rgmii_phy0>;
>>> +	phy-mode = "rgmii-rxid";
>>
>> See Andrew's remark on v1 of this patch.
> 
> Hi John
> 
> If you have questions, please ask. It is not a good idea to silently
> ignore reviewers comments. Either do something about it, ask
> questions, or politely argue why the reviewer is wrong, because
> sometimes we are.
> 
Hi Andrew,
Thanks for your feedback and the link to the RGMII delays discussion. I 
assumed you suggested switching to phy-mode = "rgmii-id" from 
rgmii-rxid. The vendor’s downstream kernel uses rgmii-rxid with tx_delay 
= <0x20>, as shown in my post. I tried rgmii-id and removed tx_delay, 
but the interface failed to get a DHCP address. Reverting to rgmii-rxid 
with the delay restored functionality. Any advice on correctly 
configuring rgmii-id or adjusting delays for this board?
Best,
John Clark

>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&eth0m0_miim
>>> +		     &eth0m0_tx_bus2
>>> +		     &eth0m0_rx_bus2
>>> +		     &eth0m0_rgmii_clk
>>> +		     &eth0m0_rgmii_bus
>>> +		     &ethm0_clk0_25m_out>;
>>> +	snps,reset-gpio = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
>>> +	snps,reset-active-low;
>>> +	snps,reset-delays-us = <0 20000 100000>;
>>
>> The snps,reset- props are depracated, please move to reset props in the
>> Ethernet PHY node.
> 
> FYI: snps,dwmac.yaml says:
> 
> snps,reset-gpio:
>      deprecated: true
>      maxItems: 1
>      description:
>        PHY Reset GPIO
> 
> Anything with 'deprecated: true' you should not be using in new DT
> blobs. Don't blindly copy vendor DT, you need to verify it is up to
> Mainline quality, and if not, bring it up to Mainline quality.
> 
>>> +	tx_delay = <0x20>;
> 
> This property probably plays a role in the issue with phy-mode.
> 
> arch/arm64/boot/dts/rockchip$ grep "rgmii-id" *
> rk3328-orangepi-r1-plus-lts.dts:	phy-mode = "rgmii-id";
> rk3566-bigtreetech-cb2.dtsi:	phy-mode = "rgmii-id";
> rk3566-nanopi-r3s.dts:	phy-mode = "rgmii-id";
> rk3566-odroid-m1s.dts:	phy-mode = "rgmii-id";
> rk3566-orangepi-3b.dtsi:	phy-mode = "rgmii-id";
> rk3566-radxa-zero-3e.dts:	phy-mode = "rgmii-id";
> rk3566-rock-3c.dts:	phy-mode = "rgmii-id";
> rk3568-evb1-v10.dts:	phy-mode = "rgmii-id";
> rk3568-evb1-v10.dts:	phy-mode = "rgmii-id";
> ...
> etc.
> 
> You might be able to learn something from these.
> 
> 	Andrew