[PATCH 3/3] ARM: dts: rockchip: add rk3036 usb2phy nodes and enable them on kylin

[Heiko Stuebner]

The rk3036 does contain a usb2phy, just until now it was just used
implicitly without additional configuration. As we now have the bits
in place for it getting actually controlled, add the necessary phy-node
to the GRF simple-mfd.

Enable the phy-ports in the same patch to not create bisectability
issues, as hooking up the phys to the usb controllers would create
probe deferrals until a board enables them. Doing everything in one
patch, solves that issue.

Only rk3036-kylin actually enabled the usb controllers, so is the only
board affected.

Signed-off-by: Heiko Stuebner <heiko at sntech.de>
---
 arch/arm/boot/dts/rockchip/rk3036-kylin.dts | 12 +++++++
 arch/arm/boot/dts/rockchip/rk3036.dtsi      | 35 +++++++++++++++++++++
 2 files changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/rockchip/rk3036-kylin.dts b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
index 4f928c7898e9..51a74f79c935 100644
--- a/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rockchip/rk3036-kylin.dts
@@ -382,6 +382,18 @@ &usb_otg {
 	status = "okay";
 };
 
+&usb2phy {
+	status = "okay";
+};
+
+&usb2phy_host {
+	status = "okay";
+};
+
+&usb2phy_otg {
+	status = "okay";
+};
+
 &vop {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/rockchip/rk3036.dtsi b/arch/arm/boot/dts/rockchip/rk3036.dtsi
index f4292b586bc2..fca21ebb224b 100644
--- a/arch/arm/boot/dts/rockchip/rk3036.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3036.dtsi
@@ -213,6 +213,8 @@ usb_otg: usb at 10180000 {
 		g-np-tx-fifo-size = <16>;
 		g-rx-fifo-size = <275>;
 		g-tx-fifo-size = <256 128 128 64 64 32>;
+		phys = <&usb2phy_otg>;
+		phy-names = "usb2-phy";
 		status = "disabled";
 	};
 
@@ -224,6 +226,8 @@ usb_host: usb at 101c0000 {
 		clocks = <&cru HCLK_OTG1>;
 		clock-names = "otg";
 		dr_mode = "host";
+		phys = <&usb2phy_host>;
+		phy-names = "usb2-phy";
 		status = "disabled";
 	};
 
@@ -342,6 +346,37 @@ cru: clock-controller at 20000000 {
 	grf: syscon at 20008000 {
 		compatible = "rockchip,rk3036-grf", "syscon", "simple-mfd";
 		reg = <0x20008000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		usb2phy: usb2phy at 17c {
+			compatible = "rockchip,rk3036-usb2phy";
+			reg = <0x017c 0x20>;
+			clocks = <&cru SCLK_OTGPHY0>;
+			clock-names = "phyclk";
+			clock-output-names = "usb480m_phy";
+			assigned-clocks = <&cru SCLK_USB480M>;
+			assigned-clock-parents = <&usb2phy>;
+			#clock-cells = <0>;
+			status = "disabled";
+
+			usb2phy_host: host-port {
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "linestate";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			usb2phy_otg: otg-port {
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "otg-bvalid", "otg-id",
+						  "linestate";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
 
 		power: power-controller {
 			compatible = "rockchip,rk3036-power-controller";
-- 
2.47.2