[PATCH v2 4/4] arm64: dts: ti: k3-am62x: Add required voltage supplies for TEVI-OV5640

[Thakkar, Devarsh]

On 5/2/2025 9:55 PM, Rishikesh Donadkar wrote:
> The device tree overlay for TEVI-OV5640 requires following voltage
> supplies as mentioned in the power section [1]
> 
> AVDD-supply: Analog voltage supply, 2.8 volts
> DOVDD-supply: Digital I/O voltage supply, 1.8 volts
> DVDD-supply: Digital core voltage supply, 3.3 volts
> 
> Add them in the DT overlay.
> 
> Link: https://www.technexion.com/wp-content/uploads/2023/09/product-brief_tevi-ov5640.pdf
> Signed-off-by: Rishikesh Donadkar <r-donadkar at ti.com>

Reviewed-by: Devarsh Thakkar <devarsht at ti.com>

Regards
Devarsh

> ---
>  .../dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso  | 32 +++++++++++++++++++
>  1 file changed, 32 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
> index b6bfdfbbdd984..fe3bc29632fa9 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
> @@ -15,6 +15,33 @@ clk_ov5640_fixed: ov5640-xclk {
>  		#clock-cells = <0>;
>  		clock-frequency = <24000000>;
>  	};
> +
> +	reg_2p8v: regulator-2p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "2P8V";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
> +
> +	reg_1p8v: regulator-1p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1P8V";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
>  };
>  
>  &main_i2c2 {
> @@ -40,6 +67,11 @@ ov5640: camera at 3c {
>  
>  				clocks = <&clk_ov5640_fixed>;
>  				clock-names = "xclk";
> +
> +				AVDD-supply = <&reg_2p8v>;
> +				DOVDD-supply = <&reg_1p8v>;
> +				DVDD-supply = <&reg_3p3v>;
> +
>  				powerdown-gpios = <&exp1 13 GPIO_ACTIVE_LOW>;
>  
>  				port {