[PATCH v1 2/4] arm64: dts: ti: k3-am62x: Add required voltage supplies for IMX219

[Devarsh Thakkar]

On 29/04/25 21:11, Rishikesh Donadkar wrote:
> The device tree overlay for the IMX219 sensor requires three voltage
> supplies to be defined: VANA (analog), VDIG (digital core), and VDDL
> (digital I/O).
> 
> Add the corresponding voltage supply definitions to avoid dtbs_check
> warnings.
> 
> Signed-off-by: Rishikesh Donadkar <r-donadkar at ti.com>

Reviewed-by: Devarsh Thakkar <devarsht at ti.com>

Regards
Devarsh
> ---
>  .../boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso  | 31 +++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
> index dd090813a32d6..149c59c071823 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
> @@ -15,6 +15,33 @@ clk_imx219_fixed: imx219-xclk {
>  		#clock-cells = <0>;
>  		clock-frequency = <24000000>;
>  	};
> +
> +	reg_2p8v: regulator-2p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "2P8V";
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
> +
> +	reg_1p8v: regulator-1p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1P8V";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
> +
> +	reg_1p2v: regulator-1p2v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1P2V";
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +		vin-supply = <&vcc_3v3_sys>;
> +		regulator-always-on;
> +	};
>  };
>  
>  &main_i2c2 {
> @@ -40,6 +67,10 @@ ov5640: camera at 10 {
>  
>  				clocks = <&clk_imx219_fixed>;
>  
> +				VANA-supply = <&reg_2p8v>;
> +				VDIG-supply = <&reg_1p8v>;
> +				VDDL-supply = <&reg_1p2v>;
> +
>  				reset-gpios = <&exp1 13 GPIO_ACTIVE_HIGH>;
>  
>  				port {