[PATCH v2 1/4] dt-bindings: net: Add MTIP L2 switch description

[Rob Herring]

On Fri, Mar 28, 2025 at 02:35:41PM +0100, Lukasz Majewski wrote:
> This patch provides description of the MTIP L2 switch available in some
> NXP's SOCs - e.g. imx287.
> 
> Signed-off-by: Lukasz Majewski <lukma at denx.de>
> ---
> Changes for v2:
> - Rename the file to match exactly the compatible
>   (nxp,imx287-mtip-switch)
> ---
>  .../bindings/net/nxp,imx287-mtip-switch.yaml  | 165 ++++++++++++++++++
>  1 file changed, 165 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/nxp,imx287-mtip-switch.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/nxp,imx287-mtip-switch.yaml b/Documentation/devicetree/bindings/net/nxp,imx287-mtip-switch.yaml
> new file mode 100644
> index 000000000000..a3e0fe7783ec
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/nxp,imx287-mtip-switch.yaml
> @@ -0,0 +1,165 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/nxp,imx287-mtip-switch.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP SoC Ethernet Switch Controller (L2 MoreThanIP switch)
> +
> +maintainers:
> +  - Lukasz Majewski <lukma at denx.de>
> +
> +description:
> +  The 2-port switch ethernet subsystem provides ethernet packet (L2)
> +  communication and can be configured as an ethernet switch. It provides the
> +  reduced media independent interface (RMII), the management data input
> +  output (MDIO) for physical layer device (PHY) management.
> +
> +properties:
> +  compatible:
> +    const: nxp,imx287-mtip--switch
> +
> +  reg:
> +    maxItems: 1
> +    description:
> +      The physical base address and size of the MTIP L2 SW module IO range
> +
> +  phy-supply:
> +    description:
> +      Regulator that powers Ethernet PHYs.
> +
> +  clocks:
> +    items:
> +      - description: Register accessing clock
> +      - description: Bus access clock
> +      - description: Output clock for external device - e.g. PHY source clock
> +      - description: IEEE1588 timer clock
> +
> +  clock-names:
> +    items:
> +      - const: ipg
> +      - const: ahb
> +      - const: enet_out
> +      - const: ptp
> +
> +  interrupts:
> +    items:
> +      - description: Switch interrupt
> +      - description: ENET0 interrupt
> +      - description: ENET1 interrupt
> +
> +  pinctrl-names: true
> +
> +  ethernet-ports:
> +    type: object
> +    additionalProperties: false
> +
> +    properties:
> +      '#address-cells':
> +        const: 1
> +      '#size-cells':
> +        const: 0
> +
> +    patternProperties:
> +      "^port@[0-9]+$":
> +        type: object
> +        description: MTIP L2 switch external ports
> +
> +        $ref: ethernet-controller.yaml#
> +        unevaluatedProperties: false
> +
> +        properties:
> +          reg:
> +            items:
> +              - enum: [1, 2]
> +            description: MTIP L2 switch port number
> +
> +          label:
> +            description: Label associated with this port
> +
> +        required:
> +          - reg
> +          - label
> +          - phy-mode
> +          - phy-handle
> +
> +  mdio:
> +    type: object
> +    $ref: mdio.yaml#
> +    unevaluatedProperties: false
> +    description:
> +      Specifies the mdio bus in the switch, used as a container for phy nodes.
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +  - interrupts
> +  - mdio
> +  - ethernet-ports
> +  - '#address-cells'
> +  - '#size-cells'
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include<dt-bindings/interrupt-controller/irq.h>
> +    switch at 800f0000 {
> +        compatible = "nxp,imx287-mtip-switch";
> +        reg = <0x800f0000 0x20000>;
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&mac0_pins_a>, <&mac1_pins_a>;
> +        phy-supply = <&reg_fec_3v3>;
> +        interrupts = <100>, <101>, <102>;
> +        clocks = <&clks 57>, <&clks 57>, <&clks 64>, <&clks 35>;
> +        clock-names = "ipg", "ahb", "enet_out", "ptp";
> +        status = "okay";
> +
> +        ethernet-ports {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                mtip_port1: port at 1 {
> +                        reg = <1>;
> +                        label = "lan0";
> +                        local-mac-address = [ 00 00 00 00 00 00 ];
> +                        phy-mode = "rmii";
> +                        phy-handle = <&ethphy0>;
> +                };
> +
> +                mtip_port2: port at 2 {
> +                        reg = <2>;
> +                        label = "lan1";
> +                        local-mac-address = [ 00 00 00 00 00 00 ];
> +                        phy-mode = "rmii";
> +                        phy-handle = <&ethphy1>;
> +                };
> +        };
> +
> +        mdio_sw: mdio {
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                reset-gpios = <&gpio2 13 0>;
> +                reset-delay-us = <25000>;
> +                reset-post-delay-us = <10000>;
> +
> +                ethphy0: ethernet-phy at 0 {
> +                        reg = <0>;
> +                        smsc,disable-energy-detect;

With a custom property, you should have a specific compatible.

> +                        /* Both PHYs (i.e. 0,1) have the same, single GPIO, */
> +                        /* line to handle both, their interrupts (AND'ed) */
> +                        interrupt-parent = <&gpio4>;
> +                        interrupts = <13 IRQ_TYPE_EDGE_FALLING>;

The error report is because the examples have to guess the number of 
provider interrupt cells and only 1 guess is supported. It guessed 1 
from above.

In any case, unless the phys are built-in and fixed, they are out of 
scope of this binding. So perhaps drop the interrupts and smsc property.

Rob