[PATCH 12/12] ARM64: dts: bcm63158: Add BCMBCA peripherals
Linus Walleij
linus.walleij at linaro.org
Fri Mar 28 00:44:02 PDT 2025
All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. On BCM63158 the PERF window was
too big so adjust it down to its real size (0x3000).
Add the watchdog, GPIO blocks, RNG, LED, second UART and DMA
blocks for the BCM63158 based on the vendor files 63158_map_part.h
and 63158_intr.h from the "bcmopen-consumer" code drop.
The DTSI file has clearly been authored for the B0 revision of
the SoC: there is an earlier A0 version, but this has
the UARTs in the legacy PERF memory space, while the B0
has opened a new peripheral window at 0xff812000 for the
three UARTs. It also has a designated AHB peripheral area
at 0xff810000 where the DMA resides, so we create new windows
for these two peripheral group reflecting the internal
structure of the B0 SoC.
This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi | 150 +++++++++++++++++++++-
1 file changed, 147 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
index 48d618e75866452a64adfdc781ac0ea3c2eff3e8..a47c5d6d034a7ae56803a651636148383acb8cc9 100644
--- a/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
@@ -1,6 +1,7 @@
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright 2022 Broadcom Ltd.
+ * This DTSI is for the B0 and later revision of the SoC
*/
#include <dt-bindings/interrupt-controller/irq.h>
@@ -119,11 +120,107 @@ gic: interrupt-controller at 1000 {
};
};
+ /* PERF Peripherals */
bus at ff800000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0x0 0x0 0xff800000 0x800000>;
+ ranges = <0x0 0x0 0xff800000 0x3000>;
+
+ /* GPIOs 0 .. 31 */
+ gpio0: gpio at 500 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x500 0x04>, <0x520 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 32 .. 63 */
+ gpio1: gpio at 504 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x504 0x04>, <0x524 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 64 .. 95 */
+ gpio2: gpio at 508 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x508 0x04>, <0x528 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 96 .. 127 */
+ gpio3: gpio at 50c {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x50c 0x04>, <0x52c 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 128 .. 159 */
+ gpio4: gpio at 510 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x510 0x04>, <0x530 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 160 .. 191 */
+ gpio5: gpio at 514 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x514 0x04>, <0x534 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 192 .. 223 */
+ gpio6: gpio at 518 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x518 0x04>, <0x538 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+ /* GPIOs 224 .. 255 */
+ gpio7: gpio at 51c {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x51c 0x04>, <0x53c 0x04>;
+ reg-names = "dirout", "dat";
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "disabled";
+ };
+
+
+ leds: led-controller at 800 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "brcm,bcm63138-leds";
+ reg = <0x800 0xdc>;
+ status = "disabled";
+ };
+
+ rng at b80 {
+ compatible = "brcm,iproc-rng200";
+ reg = <0xb80 0x28>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ };
hsspi: spi at 1000 {
#address-cells = <1>;
@@ -150,14 +247,61 @@ nandcs: nand at 0 {
reg = <0>;
};
};
+ };
+
+ /* B0 AHB Peripherals */
+ bus at ff810000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0xff810000 0x2000>;
+
+ pl081_dma: dma-controller at 1000 {
+ compatible = "arm,pl081", "arm,primecell";
+ // The magic B105F00D info is missing
+ arm,primecell-periphid = <0x00041081>;
+ reg = <0x1000 0x1000>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+ clocks = <&periph_clk>;
+ clock-names = "apb_pclk";
+ #dma-cells = <2>;
+ };
+ };
+
+ /* B0 ARM UART Peripheral block */
+ bus at ff812000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0xff812000 0x3000>;
- uart0: serial at 12000 {
+ uart0: serial at 0 {
compatible = "arm,pl011", "arm,primecell";
- reg = <0x12000 0x1000>;
+ reg = <0x0 0x1000>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&uart_clk>, <&uart_clk>;
clock-names = "uartclk", "apb_pclk";
status = "disabled";
};
+
+ uart1: serial at 1000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x1000 0x1000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_clk>, <&uart_clk>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart2: serial at 2000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x2000 0x1000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_clk>, <&uart_clk>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
};
};
--
2.48.1
More information about the linux-arm-kernel
mailing list