[PATCH v3 5/8] arm64: dts: freescale: add Ka-Ro Electronics tx8p-ml81 COMy
Frank Li
Frank.li at nxp.com
Thu Mar 27 09:18:28 PDT 2025
On Thu, Mar 27, 2025 at 04:52:40PM +0100, Maud Spierings via B4 Relay wrote:
> From: Maud Spierings <maudspierings at gocontroll.com>
>
> The Ka-Ro Electronics tx8p-ml81 is a COM based on the imx8mp SOC. It has
> 2 GB or ram and 8 GB of eMMC storage on board.
>
> Add it to enable boards based on this Module
>
> Signed-off-by: Maud Spierings <maudspierings at gocontroll.com>
> ---
> .../arm64/boot/dts/freescale/imx8mp-tx8p-ml81.dtsi | 549 +++++++++++++++++++++
> 1 file changed, 549 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tx8p-ml81.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-tx8p-ml81.dtsi
> new file mode 100644
> index 0000000000000000000000000000000000000000..9c4304e909b96afeb62962198da377319eda8506
> --- /dev/null
New dts files, suggest run https://github.com/lznuaa/dt-format to make
nodes and property ordered.
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-tx8p-ml81.dtsi
> @@ -0,0 +1,549 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2020 Lothar Waßmann <LW at KARO-electronics.de>
> + * 2025 Maud Spierings <maudspierings at gocontroll.com>
> + */
> +
> +#include "imx8mp.dtsi"
> +
> +/ {
> + /* PHY regulator */
> + regulator-3v3-etn {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_3v3_etn>;
> + regulator-name = "3v3-etn";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <®_vdd_3v3>;
> + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <®_vdd_arm>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <®_vdd_arm>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <®_vdd_arm>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <®_vdd_arm>;
> +};
> +
> +
> +&eqos {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&pinctrl_eqos>;
> + pinctrl-1 = <&pinctrl_eqos_sleep>;
> + assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>,
> + <&clk IMX8MP_CLK_ENET_QOS_TIMER>,
> + <&clk IMX8MP_CLK_ENET_QOS>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
> + <&clk IMX8MP_SYS_PLL2_100M>,
> + <&clk IMX8MP_SYS_PLL2_50M>;
> + assigned-clock-rates = <0>, <100000000>, <50000000>;
> + phy-mode = "rmii";
> + phy-handle = <ðphy0>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
"compatible" should be first property.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ethphy_rst_b>;
> + reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
> + reset-delay-us = <25000>;
> +
> + ethphy0: ethernet-phy at 0 {
> + reg = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ethphy_int_b>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
> + clocks = <&clk IMX8MP_CLK_ENET_QOS>;
> + smsc,disable-energy-detect;
> + };
> + };
> +};
> +
> +&gpio1 {
> + gpio-line-names = "SODIMM_152",
> + "SODIMM_42",
> + "PMIC_WDOG_B SODIMM_153",
> + "PMIC_IRQ_B",
> + "SODIMM_154",
> + "SODIMM_155",
> + "SODIMM_156",
> + "SODIMM_157",
> + "SODIMM_158",
> + "SODIMM_159",
> + "SODIMM_161",
> + "SODIMM_162",
> + "SODIMM_34",
> + "SODIMM_36",
> + "SODIMM_27",
> + "SODIMM_28",
> + "ENET_MDC",
> + "ENET_MDIO",
> + "",
> + "ENET_XTAL1/CLKIN",
> + "ENET_TXD1",
> + "ENET_TXD0",
> + "ENET_TXEN",
> + "ENET_POWER",
> + "ENET_COL/CRS_DV",
> + "ENET_RXER",
> + "ENET_RXD0",
> + "ENET_RXD1",
> + "",
> + "",
> + "",
> + "";
> +};
> +
> +&gpio2 {
> + gpio-line-names = "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "SODIMM_51",
> + "SODIMM_57",
> + "SODIMM_56",
> + "SODIMM_52",
> + "SODIMM_53",
> + "SODIMM_54",
> + "SODIMM_55",
> + "SODIMM_15",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "";
> +};
> +
> +&gpio3 {
> + gpio-line-names = "",
> + "",
> + "EMMC_DS",
> + "EMMC_DAT5",
> + "EMMC_DAT6",
> + "EMMC_DAT7",
> + "",
> + "",
> + "",
> + "",
> + "EMMC_DAT0",
> + "EMMC_DAT1",
> + "EMMC_DAT2",
> + "EMMC_DAT3",
> + "",
> + "EMMC_DAT4",
> + "",
> + "EMMC_CLK",
> + "EMMC_CMD",
> + "SODIMM_75",
> + "SODIMM_145",
> + "SODIMM_163",
> + "SODIMM_164",
> + "SODIMM_165",
> + "SODIMM_143",
> + "SODIMM_144",
> + "SODIMM_72",
> + "SODIMM_73",
> + "SODIMM_74",
> + "SODIMM_93",
> + "",
> + "";
> +};
> +
> +&gpio4 {
> + gpio-line-names = "SODIMM_98",
> + "SODIMM_99",
> + "SODIMM_100",
> + "SODIMM_101",
> + "SODIMM_45",
> + "SODIMM_43",
> + "SODIMM_105",
> + "SODIMM_106",
> + "SODIMM_107",
> + "SODIMM_108",
> + "SODIMM_104",
> + "SODIMM_103",
> + "SODIMM_115",
> + "SODIMM_114",
> + "SODIMM_113",
> + "SODIMM_112",
> + "SODIMM_109",
> + "SODIMM_110",
> + "SODIMM_95",
> + "SODIMM_96",
> + "SODIMM_97",
> + "ENET_nINT",
> + "ENET_nRST",
> + "SODIMM_84",
> + "SODIMM_87",
> + "SODIMM_86",
> + "SODIMM_85",
> + "SODIMM_83",
> + "",
> + "SODIMM_66",
> + "SODIMM_65",
> + "";
> +};
> +
> +&gpio5 {
> + gpio-line-names = "",
> + "",
> + "",
> + "SODIMM_76",
> + "SODIMM_81",
> + "SODIMM_146",
> + "SODIMM_48",
> + "SODIMM_46",
> + "SODIMM_47",
> + "SODIMM_44",
> + "SODIMM_49",
> + "",
> + "SODIMM_70",
> + "SODIMM_69",
> + "PMIC_SCL",
> + "PMIC_SDA",
> + "SODIMM_41",
> + "SODIMM_40",
> + "SODIMM_148",
> + "SODIMM_149",
> + "SODIMM_150",
> + "SODIMM_151",
> + "SODIMM_60",
> + "SODIMM_59",
> + "SODIMM_64",
> + "SODIMM_63",
> + "SODIMM_62",
> + "SODIMM_61",
> + "SODIMM_68",
> + "SODIMM_67",
> + "",
> + "";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + clock-frequency = <400000>;
> + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + pmic at 25 {
> + reg = <0x25>;
> + compatible = "nxp,pca9450c";
Compatible is first, reg is second.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> +
> + regulators {
> + reg_vdd_soc: BUCK1 {
> + regulator-name = "vdd-soc";
> + regulator-min-microvolt = <805000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + reg_vdd_arm: BUCK2 {
> + regulator-name = "vdd-core";
> + regulator-min-microvolt = <805000>;
> + regulator-max-microvolt = <950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + };
> +
> + reg_vdd_3v3: BUCK4 {
> + regulator-name = "3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_nvcc_nand: BUCK5 {
> + regulator-name = "nvcc-nand";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_nvcc_dram: BUCK6 {
> + regulator-name = "nvcc-dram";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_snvs_1v8: LDO1 {
> + regulator-name = "snvs-1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-always-on;
> + };
> +
> + reg_vdda_1v8: LDO3 {
> + regulator-name = "vdda-1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4_reg: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo5_reg: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&usdhc3 { /* eMMC */
> + max-frequency = <200000000>;
> + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
> + assigned-clock-rates = <200000000>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + vmmc-supply = <®_vdd_3v3>;
> + vqmmc-supply = <®_nvcc_nand>;
> + voltage-ranges = <3300 3300>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_eqos: eqosgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_ENET_TD2__CCM_ENET_QOS_CLOCK_GENERATE_REF_CLK
> + (MX8MP_DSE_X4 | MX8MP_PULL_UP | MX8MP_PULL_ENABLE | MX8MP_SION)
> + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC
> + (MX8MP_DSE_X4 | MX8MP_PULL_UP | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO
> + (MX8MP_DSE_X4 | MX8MP_PULL_UP | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST)
> + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST)
> + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_RXC__ENET_QOS_RX_ER
> + (MX8MP_FSEL_FAST | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST)
> + >;
> + };
> +
> + pinctrl_eqos_sleep: eqos-sleep-grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_ENET_TD2__GPIO1_IO19
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_MDC__GPIO1_IO16
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_MDIO__GPIO1_IO17
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_TD0__GPIO1_IO21
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_TD1__GPIO1_IO20
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_RD0__GPIO1_IO26
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_RD1__GPIO1_IO27
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_RXC__GPIO1_IO25
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_RX_CTL__GPIO1_IO24
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_ENET_TX_CTL__GPIO1_IO22
> + (MX8MP_ODE_ENABLE | MX8MP_PULL_ENABLE)
> + >;
> + };
> +
> + pinctrl_ethphy_int_b: ethphy-int-bgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21
> + (MX8MP_FSEL_FAST | MX8MP_HYS_SCHMITT)
> + >;
> + };
> +
> + pinctrl_ethphy_rst_b: ethphy-rst-bgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22
> + (MX8MP_PULL_UP | MX8MP_PULL_ENABLE)
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL
> + (MX8MP_DSE_X6 | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE | MX8MP_SION)
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA
> + (MX8MP_DSE_X6 | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE | MX8MP_SION)
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1-gpiogrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14
> + (MX8MP_DSE_X6 | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE | MX8MP_SION)
> + MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15
> + (MX8MP_DSE_X6 | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE | MX8MP_SION)
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03
> + (MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + >;
> + };
> +
> + pinctrl_reg_3v3_etn: reg-3v3-etngrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_ENET_TXC__GPIO1_IO23
> + (MX8MP_PULL_UP | MX8MP_PULL_ENABLE)
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK
> + (MX8MP_FSEL_FAST | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
It is much better than hex value
The most are the same. Can you define helper macro to reduce copy long OR
for example
#define USDHC_DEFAULT (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
so pinctrl_usdhc3_100mhz
fsl,pins = <... (MX8MP_DSE_X2 | USDHC_DEFAULT);
usdhc3-200mhzgrp
fsl,pins = <... (MX8MP_DSE_X6 | USDHC_DEFAULT);
Frank
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7
> + (MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE
> + (MX8MP_FSEL_FAST | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE
> + (MX8MP_DSE_X2 | MX8MP_FSEL_FAST | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_PULL_UP | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE
> + (MX8MP_DSE_X6 | MX8MP_FSEL_FAST | MX8MP_HYS_SCHMITT | MX8MP_PULL_ENABLE)
> + >;
> + };
> +};
>
> --
> 2.49.0
>
>
More information about the linux-arm-kernel
mailing list