[PATCH v10 01/10] clk: qcom: clk-alpha-pll: Add support for dynamic update for slewing PLLs

Dmitry Baryshkov dmitry.baryshkov at oss.qualcomm.com
Fri Jun 27 05:37:09 PDT 2025


On 27/06/2025 13:13, Taniya Das wrote:
> 
> 
> On 6/25/2025 5:17 PM, Dmitry Baryshkov wrote:
>> On Wed, Jun 25, 2025 at 04:13:26PM +0530, Taniya Das wrote:
>>> The alpha PLLs which slew to a new frequency at runtime would require
>>> the PLL to calibrate at the mid point of the VCO. Add the new PLL ops
>>> which can support the slewing of the PLL to a new frequency.
>>>
>>> Reviewed-by: Imran Shaik <quic_imrashai at quicinc.com>
>>> Signed-off-by: Taniya Das <quic_tdas at quicinc.com>
>>> ---
>>>   drivers/clk/qcom/clk-alpha-pll.c | 169 +++++++++++++++++++++++++++++++++++++++
>>>   drivers/clk/qcom/clk-alpha-pll.h |   1 +
>>>   2 files changed, 170 insertions(+)
>>>
> 
>>> +	/*
>>> +	 * Dynamic pll update will not support switching frequencies across
>>> +	 * vco ranges. In those cases fall back to normal alpha set rate.
>>> +	 */
>>> +	if (curr_vco->val != vco->val)
>>> +		return clk_alpha_pll_set_rate(hw, rate, parent_rate);
>>> +
>>> +	a <<= ALPHA_REG_BITWIDTH - ALPHA_BITWIDTH;
>>> +
>>> +	regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
>>> +	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), lower_32_bits(a));
>>> +	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL_U(pll), upper_32_bits(a));
>>
>> We have code that does this in __clk_alpha_pll_set_rate() and now you
>> are adding two more copies. Please extract PLL_L_VAL, PLL_ALPHA_VAL and
>> PLL_USER_CTL / PLL_VCO_MASK into a helper function.
>>
> 
> Dmitry, I was thinking of implementing the following as a reusable
> helper since it can be leveraged by most of the functions. I'd
> appreciate your suggestions or feedback.

The code below looks good to me. Please use 'alpha' instead of 'a'.

> 
> static void clk_alpha_pll_update_configs(struct clk_alpha_pll *pll,
> const struct pll_vco *vco, u32 l, u64 a, u32 alpha_width, bool alpha_en)
> {
> 	regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
> 
> 	if (alpha_width > ALPHA_BITWIDTH)
> 		a <<= alpha_width - ALPHA_BITWIDTH;
> 
> 	if (alpha_width > 32)
> 		regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL_U(pll), upper_32_bits(a));
> 
> 	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), lower_32_bits(a));
> 
> 	if (vco) {
> 		regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll),
> 				   PLL_VCO_MASK << PLL_VCO_SHIFT,
> 				   vco->val << PLL_VCO_SHIFT);
> 	}
> 
> 	if (alpha_en)
> 		regmap_set_bits(pll->clkr.regmap, PLL_USER_CTL(pll), PLL_ALPHA_EN);
> }
> 
> 
>>> +
>>> +	/* Ensure that the write above goes before slewing the PLL */
>>> +	mb();
>>> +
>>> +	if (clk_hw_is_enabled(hw))
>>> +		return clk_alpha_pll_slew_update(pll);
>>> +
>>> +	return 0;
>>> +}
>>> +
>>> +/*
>>> + * Slewing plls should be bought up at frequency which is in the middle of the
>>> + * desired VCO range. So after bringing up the pll at calibration freq, set it
>>> + * back to desired frequency(that was set by previous clk_set_rate).
> 
>>>
>>
> 


-- 
With best wishes
Dmitry



More information about the linux-arm-kernel mailing list