[PATCHv4 1/6] arm64: dts: ti: Add bootph property to nodes at source for am62a
Paresh Bhagat
p-bhagat at ti.com
Tue Jun 24 02:13:45 PDT 2025
Hi Bryan,
On 23/06/25 20:15, Bryan Brattlof wrote:
> On June 23, 2025 thus sayeth Paresh Bhagat:
>> Add bootph property directly into the original definitions of relevant
>> nodes (e.g., power domains, USB controllers, and other peripherals)
>> within their respective DTSI files (ex. main, mcu, and wakeup)i for
>> am62a.
>>
>> By defining bootph in the nodes source definitions instead of appending
>> it later in final DTS files, this change ensures that the property is
>> inherently present wherever the nodes are reused across derived device
>> trees.
>>
>> Signed-off-by: Paresh Bhagat <p-bhagat at ti.com>
>> ---
>> arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 15 +++++++++++++++
>> arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi | 1 +
>> arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi | 3 +++
>> arch/arm64/boot/dts/ti/k3-am62a.dtsi | 3 +++
>> 4 files changed, 22 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
>> index 63e097ddf988..1b7fe4487475 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
>> @@ -51,6 +51,7 @@ phy_gmii_sel: phy at 4044 {
>> compatible = "ti,am654-phy-gmii-sel";
>> reg = <0x4044 0x8>;
>> #phy-cells = <1>;
>> + bootph-all;
>> };
>>
>> epwm_tbclk: clock-controller at 4130 {
>> @@ -84,6 +85,7 @@ dmss: bus at 48000000 {
>> #size-cells = <2>;
>> dma-ranges;
>> ranges = <0x00 0x48000000 0x00 0x48000000 0x00 0x06000000>;
>> + bootph-all;
>>
>> ti,sci-dev-id = <25>;
>>
>> @@ -96,6 +98,7 @@ secure_proxy_main: mailbox at 4d000000 {
>> #mbox-cells = <1>;
>> interrupt-names = "rx_012";
>> interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
>> + bootph-all;
>> };
>>
>> inta_main_dmss: interrupt-controller at 48000000 {
>> @@ -131,6 +134,7 @@ main_bcdma: dma-controller at 485c0100 {
>> ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
>> ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
>> ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
>> + bootph-all;
>> };
>>
>> main_pktdma: dma-controller at 485c0000 {
>> @@ -167,6 +171,7 @@ main_pktdma: dma-controller at 485c0000 {
>> <0x2c>, /* FLOW_CPSW_RX_CHAN */
>> <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
>> <0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
>> + bootph-all;
>> };
>> };
>>
>> @@ -216,20 +221,24 @@ dmsc: system-controller at 44043000 {
>> mbox-names = "rx", "tx";
>> mboxes = <&secure_proxy_main 12>,
>> <&secure_proxy_main 13>;
>> + bootph-all;
>>
>> k3_pds: power-controller {
>> compatible = "ti,sci-pm-domain";
>> #power-domain-cells = <2>;
>> + bootph-all;
>> };
>>
>> k3_clks: clock-controller {
>> compatible = "ti,k2g-sci-clk";
>> #clock-cells = <2>;
>> + bootph-all;
>> };
>>
>> k3_reset: reset-controller {
>> compatible = "ti,sci-reset";
>> #reset-cells = <2>;
>> + bootph-all;
>> };
>> };
>>
>> @@ -254,6 +263,7 @@ secure_proxy_sa3: mailbox at 43600000 {
>> * firmware on non-MPU processors
>> */
>> status = "disabled";
>> + bootph-all;
>> };
>>
>> main_pmx0: pinctrl at f4000 {
>> @@ -262,6 +272,7 @@ main_pmx0: pinctrl at f4000 {
>> #pinctrl-cells = <1>;
>> pinctrl-single,register-width = <32>;
>> pinctrl-single,function-mask = <0xffffffff>;
>> + bootph-all;
>> };
>>
>> main_esm: esm at 420000 {
>> @@ -282,6 +293,7 @@ main_timer0: timer at 2400000 {
>> assigned-clock-parents = <&k3_clks 36 3>;
>> power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
>> ti,timer-pwm;
>> + bootph-all;
>> };
>>
>> main_timer1: timer at 2410000 {
>> @@ -653,6 +665,7 @@ usb0: usb at 31000000 {
>> dr_mode = "otg";
>> snps,usb2-gadget-lpm-disable;
>> snps,usb2-lpm-disable;
>> + bootph-all;
>> };
>> };
>>
>> @@ -745,6 +758,7 @@ cpsw_port1: port at 1 {
>> phys = <&phy_gmii_sel 1>;
>> mac-address = [00 00 00 00 00 00];
>> ti,syscon-efuse = <&cpsw_mac_syscon 0x0>;
>> + bootph-all;
>> };
>>
>> cpsw_port2: port at 2 {
>> @@ -764,6 +778,7 @@ cpsw3g_mdio: mdio at f00 {
>> clocks = <&k3_clks 13 0>;
>> clock-names = "fck";
>> bus_freq = <1000000>;
>> + bootph-all;
>> };
>>
>> cpts at 3d000 {
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
>> index ee961ced7208..df4aa131097f 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
>> @@ -12,6 +12,7 @@ mcu_pmx0: pinctrl at 4084000 {
>> #pinctrl-cells = <1>;
>> pinctrl-single,register-width = <32>;
>> pinctrl-single,function-mask = <0xffffffff>;
>> + bootph-all;
>> };
>>
>> mcu_esm: esm at 4100000 {
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
>> index 259ae6ebbfb5..86aae252385c 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
>> @@ -13,10 +13,12 @@ wkup_conf: bus at 43000000 {
>> #address-cells = <1>;
>> #size-cells = <1>;
>> ranges = <0x00 0x00 0x43000000 0x20000>;
>> + bootph-all;
>>
>> chipid: chipid at 14 {
>> compatible = "ti,am654-chipid";
>> reg = <0x14 0x4>;
>> + bootph-all;
>> };
>>
>> opp_efuse_table: syscon at 18 {
>> @@ -67,6 +69,7 @@ wkup_uart0: serial at 0 {
>> reg = <0 0x100>;
>> interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
>> status = "disabled";
>> + bootph-pre-ram;
>> };
>> };
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62a.dtsi b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
>> index 4d79b3e9486a..54eab2c93eff 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62a.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
>> @@ -50,6 +50,7 @@ cbass_main: bus at f0000 {
>> compatible = "simple-bus";
>> #address-cells = <2>;
>> #size-cells = <2>;
>> + bootph-all;
> We only need to add the bootph-* properties to the leaf nodes. U-Boot is
> smart enough to propagate these properties all the way to the root when
> it's pruning the device tree for the bootloaders.
>
> ~Bryan
Will fix this. Thanks
More information about the linux-arm-kernel
mailing list