[PATCH 5/5] arm64: dts: allwinner: t527: Add OrangePi 4A board

Chen-Yu Tsai wens at kernel.org
Thu Jun 19 10:30:07 PDT 2025 

From: Chen-Yu Tsai <wens at csie.org>

The OrangePi 4A is a typical Raspberry Pi model B sized development
board from Xunlong designed around an Allwinner T527 SoC.

The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header

Add a device tree for it, enabling all peripherals currently supported.

Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun55i-t527-orangepi-4a.dts | 378 ++++++++++++++++++
 2 files changed, 379 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 773cc02a13d0..780aeba0f3a4 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -57,3 +57,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-sp.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun55i-a527-cubie-a5e.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun55i-h728-x96qpro+.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-avaota-a1.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-orangepi-4a.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
new file mode 100644
index 000000000000..8a62607e584c
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright (C) 2025 Chen-Yu Tsai <wens at csie.org>
+ */
+
+/dts-v1/;
+
+#include "sun55i-a523.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "OrangePi 4A";
+	compatible = "xunlong,orangepi-4a", "allwinner,sun55i-t527";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ext_osc32k: ext-osc32k-clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "ext_osc32k";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* PWM capable pin, but PWM isn't supported yet. */
+		led {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+		};
+	};
+
+	wifi_pwrseq: pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 1 1 GPIO_ACTIVE_LOW>; /* PM1 */
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_vcc5v>;
+		gpio = <&r_pio 0 4 GPIO_ACTIVE_HIGH>;	/* PL4 */
+		enable-active-high;
+	};
+
+	reg_pcie_vcc3v3: regulator-pcie-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-pcie-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v>;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>;	/* PL8 */
+		enable-active-high;
+	};
+
+	reg_usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_vcc5v>;
+		gpio = <&r_pio 0 12 GPIO_ACTIVE_HIGH>;	/* PL12 */
+		enable-active-high;
+	};
+
+	reg_vcc5v: regulator-vcc5v {
+		/* board wide 5V supply from USB type-C port */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_cldo3>;
+	cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_dldo1_323>;
+	vqmmc-supply = <&reg_bldo1>;
+	status = "okay";
+
+	brcmf: wifi at 1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&r_pio>;
+		interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	bus-width = <8>;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&reg_cldo3>;
+	vqmmc-supply = <&reg_cldo1>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_cldo3>;	/* via VCC-IO */
+	vcc-pc-supply = <&reg_cldo1>;
+	vcc-pd-supply = <&reg_cldo3>;
+	vcc-pe-supply = <&reg_aldo2>;
+	vcc-pf-supply = <&reg_cldo3>;	/* VCC-IO for 3.3v; VCC-MCSI for 1.8v */
+	vcc-pg-supply = <&reg_bldo1>;
+	vcc-ph-supply = <&reg_cldo3>;	/* via VCC-IO */
+	vcc-pi-supply = <&reg_cldo3>;
+	vcc-pj-supply = <&reg_cldo1>;
+	vcc-pk-supply = <&reg_cldo1>;
+};
+
+&r_i2c0 {
+	status = "okay";
+
+	axp717: pmic at 35 {
+		compatible = "x-powers,axp717";
+		reg = <0x35>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupts-extended = <&nmi_intc 0 IRQ_TYPE_LEVEL_LOW>;
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+		vin4-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			/* Supplies the "little" cluster (1.4 GHz cores) */
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1160000>;
+				regulator-name = "vdd-cpul";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <920000>;
+				regulator-max-microvolt = <920000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <1160000>;
+				regulator-max-microvolt = <1160000>;
+				regulator-name = "vcc-dram";
+			};
+
+			reg_dcdc4: dcdc4 {
+				/* feeds 3.3V pin on GPIO header */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vdd-io";
+			};
+
+			reg_aldo1: aldo1 {
+				regulator-name = "avdd-csi";
+			};
+
+			reg_aldo2: aldo2 {
+				regulator-name = "vcc-pe";
+			};
+
+			reg_aldo3: aldo3 {
+				/* supplies the I2C pins for this PMIC */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-pl-usb";
+			};
+
+			reg_aldo4: aldo4 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pll-dxco-avcc";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pg-wifi";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pm-lpddr";
+			};
+
+			reg_bldo3: bldo3 {
+				regulator-name = "dvdd-csi";
+			};
+
+			reg_bldo4: bldo4 {
+				/* not connected */
+			};
+
+			reg_cldo1: cldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-cvp-pc-lvds-mcsi-pk-efuse-pcie-edp-1v8";
+			};
+
+			reg_cldo2: cldo2 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-csi";
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-io-mmc-nand-pd-pi-usb";
+			};
+
+			reg_cldo4: cldo4 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-3v3-phy1-lcd";
+			};
+
+			reg_cpusldo: cpusldo {
+				/* supplies the management core */
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdd-cpus";
+			};
+		};
+	};
+
+	axp323: pmic at 36 {
+		compatible = "x-powers,axp323";
+		reg = <0x36>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		status = "okay";
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1_323: aldo1 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-wifi";
+			};
+
+			reg_dldo1_323: dldo1 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-wifi2";
+			};
+
+			/* Supplies the "big" cluster (1.8 GHz cores) */
+			reg_dcdc1_323: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-name = "vdd-cpub";
+			};
+
+			/* DCDC2 is polyphased with DCDC1 */
+
+			/* Some RISC-V management core related voltage */
+			reg_dcdc3_323: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdd-dnr";
+			};
+		};
+	};
+};
+
+&r_pio {
+/*
+ * Specifying the supply would create a circular dependency.
+ *
+ *	vcc-pl-supply = <&reg_aldo3>;
+ */
+	vcc-pm-supply = <&reg_bldo2>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_aldo1_323>;
+		vddio-supply = <&reg_bldo1>;
+		device-wakeup-gpios = <&r_pio 1 3 GPIO_ACTIVE_HIGH>; /* PM3 */
+		host-wakeup-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
+		shutdown-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+	};
+};
+
+&usb_otg {
+	 /*
+	  * The OTG controller is connected to one of the type-A ports.
+	  * There is a regulator, controlled by a GPIO, to provide VBUS power
+	  * to the port, and a VBUSDET GPIO, to detect externally provided
+	  * power. But without ID or CC pins there is no real way to do a
+	  * runtime role detection.
+	  */
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_vbus-supply = <&reg_otg_vbus>;
+	usb0_vbus_det-gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
+	usb1_vbus-supply = <&reg_usb_vbus>;
+	status = "okay";
+};
-- 
2.39.5

More information about the linux-arm-kernel mailing list