[PATCH v3 9/9] arm64: dts: exynos: ExynosAutov920: add USB and USB SS combo phy nodes

[Pritam Manohar Sutar]

Hi Neil, 

> -----Original Message-----
> From: neil.armstrong at linaro.org <neil.armstrong at linaro.org>
> Sent: 13 June 2025 02:42 PM
> To: Pritam Manohar Sutar <pritam.sutar at samsung.com>; vkoul at kernel.org;
> kishon at kernel.org; robh at kernel.org; krzk+dt at kernel.org;
> conor+dt at kernel.org; alim.akhtar at samsung.com; andre.draszik at linaro.org;
> peter.griffin at linaro.org; kauschluss at disroot.org;
> ivo.ivanov.ivanov1 at gmail.com; m.szyprowski at samsung.com;
> s.nawrocki at samsung.com
> Cc: linux-phy at lists.infradead.org; devicetree at vger.kernel.org; linux-
> kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org; linux-
> samsung-soc at vger.kernel.org; rosa.pila at samsung.com;
> dev.tailor at samsung.com; faraz.ata at samsung.com;
> muhammed.ali at samsung.com; selvarasu.g at samsung.com
> Subject: Re: [PATCH v3 9/9] arm64: dts: exynos: ExynosAutov920: add USB
> and USB SS combo phy nodes
> 
> On 13/06/2025 07:56, Pritam Manohar Sutar wrote:
> > Update the USB 3.1 DRD controller and USB31DRD phy nodes to support SS
> > combo phy for this soc.
> >
> > The USB 3.1 DRD controller has the following features:
> > * DWC3 compatible
> > * compliant with both USB device 3.1 and USB device 2.0 standards
> > * compliant with USB host 3.1 and USB host 2.0 standards
> > * supports USB device 3.1 and USB device 2.0 interfaces
> > * supports USB host 3.1 and USB host 2.0 interfaces
> > * full-speed (12 Mbps) and high-speed (480 Mbps) modes with USB device
> >    2.0 interface
> > * super-speed (5 Gbps) mode with USB device 3.1 Gen1 interface
> > * super-speed plus (10 Gbps) mode with USB device 3.1 Gen2 interface
> > * single USB port which can be used for USB 3.1 or USB 2.0
> > * on-chip USB PHY transceiver
> > * supports up to 16 bi-directional endpoints
> > * compliant with xHCI 1.1 specification
> >
> > USB3.1 SSP+(10Gbps) is supported in this commit and SS phy in combo
> > phy only supports PIPE3 interface and it is added in index 0 of SS phy.
> > UTMI+ and PIPE3 PHY interfaces are specified in "phys" property,
> > UTMI+ (index 0 HS phy) and PIPE3 (index 0 SS phy).
> >
> > Signed-off-by: Pritam Manohar Sutar <pritam.sutar at samsung.com>
> > ---
> >   .../arm64/boot/dts/exynos/exynosautov920-sadk.dts |  4 ++++
> >   arch/arm64/boot/dts/exynos/exynosautov920.dtsi    | 15
> +++++++++++++--
> >   2 files changed, 17 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts
> > b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts
> > index a21386bd9af3..40588f7c9998 100644
> > --- a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts
> > +++ b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts
> > @@ -88,6 +88,10 @@ &xtcxo {
> >   };
> >
> >   /* usb */
> > +&usbdrd31_ssphy {
> > +	status = "okay";
> > +};
> > +
> >   &usbdrd31_hsphy {
> >   	status = "okay";
> >   };
> > diff --git a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> > b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> > index 4efc005cae80..5ee7fad346b9 100644
> > --- a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> > +++ b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> > @@ -1048,6 +1048,17 @@ pinctrl_hsi1: pinctrl at 16450000 {
> >   			interrupts = <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>;
> >   		};
> >
> > +		usbdrd31_ssphy: phy at 16480000 {
> > +			compatible = "samsung,exynosautov920-usb31drd-
> ssphy";
> > +			reg = <0x16480000 0x0200>;
> > +			clocks = <&cmu_hsi1 CLK_MOUT_HSI1_NOC_USER>,
> > +				 <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>;
> > +			clock-names = "phy", "ref";
> > +			#phy-cells = <1>;
> > +			samsung,pmu-syscon = <&pmu_system_controller>;
> > +			status = "disabled";
> > +		};
> > +
> >   		usbdrd31_hsphy: phy at 16490000 {
> >   			compatible = "samsung,exynosautov920-usbdrd-
> hsphy";
> >   			reg = <0x16490000 0x0200>;
> > @@ -1109,8 +1120,8 @@ usbdrd31_dwc3: usb at 0 {
> >   					 <&cmu_hsi1
> CLK_MOUT_HSI1_USBDRD>;
> >   				clock-names = "ref", "susp_clk";
> >   				interrupts = <GIC_SPI 491
> IRQ_TYPE_LEVEL_HIGH>;
> > -				phys = <&usbdrd31_hsphy 0>;
> > -				phy-names = "usb2-phy";
> > +				phys = <&usbdrd31_hsphy 0>,
> <&usbdrd31_ssphy 0>;
> > +				phy-names = "usb2-phy", "usb3-phy";
> >   				snps,has-lpm-erratum;
> >   				snps,dis_u2_susphy_quirk;
> >   				snps,dis_u3_susphy_quirk;
> 
> I think at least patch 6 & 9 should be squashed.
> 

Patch 6 and 9 are posted to add support for HS and SS phys in combo phy separately.
We will squash them in next version of patch-set (v4). 

> Neil

Thank you.

Regards,
Pritam