[PATCH v3 9/9] arm64: dts: exynos: ExynosAutov920: add USB and USB SS combo phy nodes

[neil.armstrong at linaro.org]

On 13/06/2025 07:56, Pritam Manohar Sutar wrote:
> Update the USB 3.1 DRD controller and USB31DRD phy nodes to support
> SS combo phy for this soc.
> 
> The USB 3.1 DRD controller has the following features:
> * DWC3 compatible
> * compliant with both USB device 3.1 and USB device 2.0 standards
> * compliant with USB host 3.1 and USB host 2.0 standards
> * supports USB device 3.1 and USB device 2.0 interfaces
> * supports USB host 3.1 and USB host 2.0 interfaces
> * full-speed (12 Mbps) and high-speed (480 Mbps) modes with USB device
>    2.0 interface
> * super-speed (5 Gbps) mode with USB device 3.1 Gen1 interface
> * super-speed plus (10 Gbps) mode with USB device 3.1 Gen2 interface
> * single USB port which can be used for USB 3.1 or USB 2.0
> * on-chip USB PHY transceiver
> * supports up to 16 bi-directional endpoints
> * compliant with xHCI 1.1 specification
> 
> USB3.1 SSP+(10Gbps) is supported in this commit and SS phy in combo
> phy only supports PIPE3 interface and it is added in index 0 of SS phy.
> UTMI+ and PIPE3 PHY interfaces are specified in "phys" property,
> UTMI+ (index 0 HS phy) and PIPE3 (index 0 SS phy).
> 
> Signed-off-by: Pritam Manohar Sutar <pritam.sutar at samsung.com>
> ---
>   .../arm64/boot/dts/exynos/exynosautov920-sadk.dts |  4 ++++
>   arch/arm64/boot/dts/exynos/exynosautov920.dtsi    | 15 +++++++++++++--
>   2 files changed, 17 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts
> index a21386bd9af3..40588f7c9998 100644
> --- a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts
> +++ b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts
> @@ -88,6 +88,10 @@ &xtcxo {
>   };
>   
>   /* usb */
> +&usbdrd31_ssphy {
> +	status = "okay";
> +};
> +
>   &usbdrd31_hsphy {
>   	status = "okay";
>   };
> diff --git a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> index 4efc005cae80..5ee7fad346b9 100644
> --- a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> @@ -1048,6 +1048,17 @@ pinctrl_hsi1: pinctrl at 16450000 {
>   			interrupts = <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>;
>   		};
>   
> +		usbdrd31_ssphy: phy at 16480000 {
> +			compatible = "samsung,exynosautov920-usb31drd-ssphy";
> +			reg = <0x16480000 0x0200>;
> +			clocks = <&cmu_hsi1 CLK_MOUT_HSI1_NOC_USER>,
> +				 <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>;
> +			clock-names = "phy", "ref";
> +			#phy-cells = <1>;
> +			samsung,pmu-syscon = <&pmu_system_controller>;
> +			status = "disabled";
> +		};
> +
>   		usbdrd31_hsphy: phy at 16490000 {
>   			compatible = "samsung,exynosautov920-usbdrd-hsphy";
>   			reg = <0x16490000 0x0200>;
> @@ -1109,8 +1120,8 @@ usbdrd31_dwc3: usb at 0 {
>   					 <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>;
>   				clock-names = "ref", "susp_clk";
>   				interrupts = <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
> -				phys = <&usbdrd31_hsphy 0>;
> -				phy-names = "usb2-phy";
> +				phys = <&usbdrd31_hsphy 0>, <&usbdrd31_ssphy 0>;
> +				phy-names = "usb2-phy", "usb3-phy";
>   				snps,has-lpm-erratum;
>   				snps,dis_u2_susphy_quirk;
>   				snps,dis_u3_susphy_quirk;

I think at least patch 6 & 9 should be squashed.

Neil