[PATCH v4 3/5] arm64: dts: qcom: x1e80100-qcp: enable pcie3 x8 slot for X1E80100-QCP

[Wenbin Yao]

From: Qiang Yu <qiang.yu at oss.qualcomm.com>

Add perst, wake and clkreq sideband signals and required regulators in
PCIe3 controller and PHY device tree node. Describe the voltage rails of
the x8 PCI slots for PCIe3 port.

Signed-off-by: Qiang Yu <qiang.yu at oss.qualcomm.com>
Signed-off-by: Wenbin Yao <quic_wenbyao at quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio at oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 118 ++++++++++++++++++++++
 1 file changed, 118 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 4dfba835a..71c44e37a 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -318,6 +318,48 @@ vreg_wcn_3p3: regulator-wcn-3p3 {
 		regulator-boot-on;
 	};
 
+	vreg_pcie_12v: regulator-pcie-12v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+
+		gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pcie_x8_12v>;
+		pinctrl-names = "default";
+	};
+
+	vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3_AUX";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8380_3_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pm_sde7_aux_3p3_en>;
+		pinctrl-names = "default";
+	};
+
+	vreg_pcie_3v3: regulator-pcie-3v3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8380_3_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pm_sde7_main_3p3_en>;
+		pinctrl-names = "default";
+};
+
 	usb-1-ss0-sbu-mux {
 		compatible = "onnn,fsusb42", "gpio-sbu-mux";
 
@@ -908,6 +950,59 @@ &mdss_dp3_phy {
 	status = "okay";
 };
 
+&pm8550ve_8_gpios {
+	pcie_x8_12v: pcie-12v-default-state {
+		pins = "gpio8";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+};
+
+&pmc8380_3_gpios {
+	pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
+		pins = "gpio8";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+
+	pm_sde7_main_3p3_en: pcie-main-3p3-default-state {
+		pins = "gpio6";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+};
+
+&pcie3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie3_default>;
+	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&pcie3_phy {
+	vdda-phy-supply = <&vreg_l3c_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie3_port {
+	vpcie12v-supply = <&vreg_pcie_12v>;
+	vpcie3v3-supply = <&vreg_pcie_3v3>;
+	vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>;
+};
+
 &pcie4 {
 	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
 	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
@@ -1119,6 +1214,29 @@ nvme_reg_en: nvme-reg-en-state {
 		bias-disable;
 	};
 
+	pcie3_default: pcie3-default-state {
+		clkreq-n-pins {
+			pins = "gpio144";
+			function = "pcie3_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio143";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-n-pins {
+			pins = "gpio145";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	pcie4_default: pcie4-default-state {
 		clkreq-n-pins {
 			pins = "gpio147";
-- 
2.34.1