[PATCH v4 5/6] phy: rockchip: naneng-combphy: Add RK3528 support
Yao Zi
ziyao at disroot.org
Wed Jul 23 22:23:55 PDT 2025
On Wed, Jul 23, 2025 at 04:51:15PM +0200, Jonas Karlman wrote:
> Hi Yao Zi,
>
> On 6/24/2025 5:37 AM, Yao Zi wrote:
> > Rockchip RK3528 integrates one naneng-combphy that is able to operate in
> > PCIe and USB3 mode. The control logic is similar to previous variants of
> > naneng-combphy but the register layout is apperantly different from the
> > RK3568 one.
> >
> > Signed-off-by: Yao Zi <ziyao at disroot.org>
> > Reviewed-by: Heiko Stuebner <heiko at sntech.de>
> > Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>
> > ---
> > .../rockchip/phy-rockchip-naneng-combphy.c | 186 +++++++++++++++++-
> > 1 file changed, 185 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> > index 1d1c7723584b..bf00a85a113b 100644
> > --- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> > +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> > @@ -20,7 +20,46 @@
> > #define REF_CLOCK_25MHz (25 * HZ_PER_MHZ)
> > #define REF_CLOCK_100MHz (100 * HZ_PER_MHZ)
> >
> > -/* COMBO PHY REG */
> > +/* RK3528 COMBO PHY REG */
> > +#define RK3528_PHYREG6 0x18
> > +#define RK3528_PHYREG6_PLL_KVCO GENMASK(12, 10)
> > +#define RK3528_PHYREG6_PLL_KVCO_VALUE 0x2
> > +#define RK3528_PHYREG6_SSC_DIR GENMASK(5, 4)
> > +#define RK3528_PHYREG6_SSC_UPWARD 0
> > +#define RK3528_PHYREG6_SSC_DOWNWARD 1
> > +
> > +#define RK3528_PHYREG40 0x100
> > +#define RK3528_PHYREG40_SSC_EN BIT(20)
> > +#define RK3528_PHYREG40_SSC_CNT GENMASK(10, 0)
> > +#define RK3528_PHYREG40_SSC_CNT_VALUE 0x17d
> > +
> > +#define RK3528_PHYREG42 0x108
> > +#define RK3528_PHYREG42_CKDRV_CLK_SEL BIT(29)
> > +#define RK3528_PHYREG42_CKDRV_CLK_PLL 0
> > +#define RK3528_PHYREG42_CKDRV_CLK_CKRCV 1
> > +#define RK3528_PHYREG42_PLL_LPF_R1_ADJ GENMASK(10, 7)
> > +#define RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE 0x9
> > +#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ GENMASK(6, 4)
> > +#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE 0x7
> > +#define RK3528_PHYREG42_PLL_KVCO_ADJ GENMASK(2, 0)
> > +#define RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE 0x0
> > +
> > +#define RK3528_PHYREG80 0x200
> > +#define RK3528_PHYREG80_CTLE_EN BIT(17)
> > +
> > +#define RK3528_PHYREG81 0x204
> > +#define RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X BIT(5)
> > +#define RK3528_PHYREG81_SLEW_RATE_CTRL GENMASK(2, 0)
> > +#define RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW 0x7
> > +
> > +#define RK3528_PHYREG83 0x20c
> > +#define RK3528_PHYREG83_RX_SQUELCH GENMASK(2, 0)
> > +#define RK3528_PHYREG83_RX_SQUELCH_VALUE 0x6
> > +
> > +#define RK3528_PHYREG86 0x218
> > +#define RK3528_PHYREG86_RTERM_DET_CLK_EN BIT(14)
> > +
> > +/* RK3568 COMBO PHY REG */
> > #define RK3568_PHYREG6 0x14
> > #define RK3568_PHYREG6_PLL_DIV_MASK GENMASK(7, 6)
> > #define RK3568_PHYREG6_PLL_DIV_SHIFT 6
> > @@ -398,6 +437,147 @@ static int rockchip_combphy_probe(struct platform_device *pdev)
> > return PTR_ERR_OR_ZERO(phy_provider);
> > }
> >
> > +static int rk3528_combphy_cfg(struct rockchip_combphy_priv *priv)
> > +{
> > + const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> > + unsigned long rate;
> > + u32 val;
> > +
> > + /* Set SSC downward spread spectrum */
> > + val = FIELD_PREP(RK3528_PHYREG6_SSC_DIR, RK3528_PHYREG6_SSC_DOWNWARD);
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG6_SSC_DIR, val, RK3528_PHYREG6);
> > +
> > + switch (priv->type) {
> > + case PHY_TYPE_PCIE:
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> > + break;
> > + case PHY_TYPE_USB3:
> > + /* Enable adaptive CTLE for USB3.0 Rx */
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG80_CTLE_EN, RK3528_PHYREG80_CTLE_EN,
> > + RK3528_PHYREG80);
> > +
> > + /* Set slow slew rate control for PI */
> > + val = FIELD_PREP(RK3528_PHYREG81_SLEW_RATE_CTRL,
> > + RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW);
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG81_SLEW_RATE_CTRL, val,
> > + RK3528_PHYREG81);
> > +
> > + /* Set CDR phase path with 2x gain */
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X,
> > + RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X, RK3528_PHYREG81);
> > +
> > + /* Set Rx squelch input filler bandwidth */
> > + val = FIELD_PREP(RK3528_PHYREG83_RX_SQUELCH, RK3528_PHYREG83_RX_SQUELCH_VALUE);
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG83_RX_SQUELCH, val, RK3528_PHYREG83);
> > +
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
>
> I suggest we add something like following here:
>
> rockchip_combphy_param_write(priv->pipe_grf, &cfg->u3otg0_port_en, true);
>
> to ensure that U3 is enabled in case boot firmware disable the U3 port.
Thanks for the hint, I'm willing to adapt it. Should we handle the case
that USB is enabled by firmware but PCIe is going to be used in kernel,
too? It's desirable to make fewer assumptions about the state set by
firmware.
P.S., I'm assuming the register should be written as "disabled" value
whenever PCIe is used, and "enabled" whenever USB is used, as
the LSB of USB_GRF_USB3OTG0_CON1 is said to be "USB 3.0 SS Port Disable
control" according to RK3588's TRM, which doesn't look like something
compatible with PCIe mode when setting to 1'b0 (port enabled). Please
correct me if I'm wrong.
Regards,
Yao Zi
> > + break;
> > + default:
> > + dev_err(priv->dev, "incompatible PHY type\n");
> > + return -EINVAL;
> > + }
> > +
> > + rate = clk_get_rate(priv->refclk);
> > +
> > + switch (rate) {
> > + case REF_CLOCK_24MHz:
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
> > + if (priv->type == PHY_TYPE_USB3) {
> > + /* Set ssc_cnt[10:0]=00101111101 & 31.5KHz */
> > + val = FIELD_PREP(RK3528_PHYREG40_SSC_CNT, RK3528_PHYREG40_SSC_CNT_VALUE);
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_CNT, val,
> > + RK3528_PHYREG40);
> > + } else if (priv->type == PHY_TYPE_PCIE) {
> > + /* tx_trim[14]=1, Enable the counting clock of the rterm detect */
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG86_RTERM_DET_CLK_EN,
> > + RK3528_PHYREG86_RTERM_DET_CLK_EN, RK3528_PHYREG86);
> > + }
> > + break;
> > + case REF_CLOCK_100MHz:
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
> > + if (priv->type == PHY_TYPE_PCIE) {
> > + /* PLL KVCO tuning fine */
> > + val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
> > + RK3528_PHYREG6);
> > +
> > + /* su_trim[6:4]=111, [10:7]=1001, [2:0]=000, swing 650mv */
> > + writel(0x570804f0, priv->mmio + RK3528_PHYREG42);
> > + }
> > + break;
> > + default:
> > + dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
> > + return -EINVAL;
> > + }
> > +
> > + if (device_property_read_bool(priv->dev, "rockchip,ext-refclk")) {
> > + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
> > +
> > + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
> > + val = FIELD_PREP(RK3528_PHYREG42_CKDRV_CLK_SEL,
> > + RK3528_PHYREG42_CKDRV_CLK_CKRCV);
> > + val |= FIELD_PREP(RK3528_PHYREG42_PLL_LPF_R1_ADJ,
> > + RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE);
> > + val |= FIELD_PREP(RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ,
> > + RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE);
> > + val |= FIELD_PREP(RK3528_PHYREG42_PLL_KVCO_ADJ,
> > + RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE);
> > + rockchip_combphy_updatel(priv,
> > + RK3528_PHYREG42_CKDRV_CLK_SEL |
> > + RK3528_PHYREG42_PLL_LPF_R1_ADJ |
> > + RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ |
> > + RK3528_PHYREG42_PLL_KVCO_ADJ,
> > + val, RK3528_PHYREG42);
> > +
> > + val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
> > + RK3528_PHYREG6);
> > + }
> > + }
> > +
> > + if (priv->type == PHY_TYPE_PCIE) {
> > + if (device_property_read_bool(priv->dev, "rockchip,enable-ssc"))
> > + rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_EN,
> > + RK3528_PHYREG40_SSC_EN, RK3528_PHYREG40);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct rockchip_combphy_grfcfg rk3528_combphy_grfcfgs = {
> > + /* pipe-phy-grf */
> > + .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 },
> > + .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 },
> > + .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 },
> > + .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 },
> > + .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 },
> > + .pipe_clk_24m = { 0x0004, 14, 13, 0x00, 0x00 },
> > + .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 },
> > + .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 },
> > + .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 },
> > + .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 },
> > + .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 },
> > + .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 },
> > + .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x110 },
> > + .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x00 },
> > + .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x101 },
> > + .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 },
>
> And adding something like this:
>
> /* pipe-grf */
> .u3otg0_port_en = { 0x0044, 15, 0, 0x0181, 0x1100 },
>
> Should be possible with ("phy: rockchip: naneng-combphy: Enable U3 OTG
> port for RK3568") [1].
>
> Most RK3528 boards I have come across this far seem to use PCIe instead
> of USB3, so having boot firmware disable U3 early (to help support USB
> gadget in boot firmware) and instead having this PHY driver re-enable U3
> when needed seem most logical to me.
>
> I will push an updated U-Boot rk3528 branch [2] where I include such
> early U3 port disable once source.denx.de is back online again.
>
> [1] https://lore.kernel.org/r/20250723072324.2246498-1-jonas@kwiboo.se
> [2] https://source.denx.de/u-boot/contributors/kwiboo/u-boot/-/commits/rk3528
>
> Regards,
> Jonas
>
> > +};
> > +
> > +static const struct rockchip_combphy_cfg rk3528_combphy_cfgs = {
> > + .num_phys = 1,
> > + .phy_ids = {
> > + 0xffdc0000,
> > + },
> > + .grfcfg = &rk3528_combphy_grfcfgs,
> > + .combphy_cfg = rk3528_combphy_cfg,
> > +};
> > +
> > static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
> > {
> > const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> > @@ -1213,6 +1393,10 @@ static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = {
> > };
> >
> > static const struct of_device_id rockchip_combphy_of_match[] = {
> > + {
> > + .compatible = "rockchip,rk3528-naneng-combphy",
> > + .data = &rk3528_combphy_cfgs,
> > + },
> > {
> > .compatible = "rockchip,rk3562-naneng-combphy",
> > .data = &rk3562_combphy_cfgs,
>
More information about the linux-arm-kernel
mailing list