[PATCH 1/5] drm/rockchip: vop2: Add high color depth support

[Cristian Ciocaltea]

Hi Andy,

On 7/22/25 9:55 AM, Andy Yan wrote:
> 
> Hello Cristian,
> 
> 在 2025-07-22 14:16:26，"Cristian Ciocaltea" <cristian.ciocaltea at collabora.com> 写道：
>> Hi Andy,
>>
>> On 7/22/25 5:24 AM, Andy Yan wrote:
>>>
>>> Hello Cristian，
>>>
>>> At 2025-07-22 01:39:04, "Cristian Ciocaltea" <cristian.ciocaltea at collabora.com> wrote:
>>>> Take the bits per color channel into consideration when computing DCLK
>>>> rate.
>>>>
>>>> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea at collabora.com>
>>>> ---
>>>> drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 3 +++
>>>> 1 file changed, 3 insertions(+)
>>>>
>>>> diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
>>>> index 186f6452a7d359f079662bc580850929632ea8fe..a714bcbb02de16267e7febbaeb1eb270c70aaef2 100644
>>>> --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
>>>> +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
>>>> @@ -1731,6 +1731,9 @@ static void vop2_crtc_atomic_enable(struct drm_crtc *crtc,
>>>> 		clock *= 2;
>>>> 	}
>>>>
>>>> +	if (vcstate->output_bpc > 8)
>>>> +		clock = DIV_ROUND_CLOSEST(clock * vcstate->output_bpc, 8);
>>>
>>>
>>> This seems not right,  regardless of the value of bpc, the dclk of VOP must be
>>> consistent with mode->crtc_clock.
>>> If the dclk of VOP is increased in accordance with the BPC ratio here, then the refresh rate of VOP will also increase proportionally.
>>> This would be inconsistent with the timing described in the mode.
>>> For a hight color depth,  the frequency needs to be increased for the HDMI PHY's clock.
>>
>> The HDMI PHY's clock is actually computed at HDMI connector framework level
>> [1], taking into account the current bpc value, which is determined as part
>> of hdmi_compute_config() [2].
>>
>> That means conn_state->hdmi.tmds_char_rate in
>> dw_hdmi_qp_rockchip_encoder_atomic_check() does already include the bpc
>> related adjustment, and we pass that directly to the PHY via
>> phy_configure().  Note there's still the need to handle bpc separately via
>> phy_configure_opts in order to setup CMN_REG(0086) [3].
>>
>> Since VOP2 switches to PHY PLL as DCLK source for modes up to 4K at 60Hz, it
>> needs to take color depth into account, to keep them in sync.  As a matter
>> of fact, the clock adjustment in VOP2 is mainly necessary for legacy
>> reasons, since HDPTX PHY allowed changing TMDS char rate via the Common
>> Clock Framework API.  We landed a proper solution for that via the HDMI PHY
>> API, hence the plan would be to make CCF API readonly after the switch to
>> PHY API is completed, which means VOP2 shouldn't deal anymore with clock
>> calculations when using the PHY PLL as DCLK source.
> 
> What I want to emphasize is that on the vop/crtc side, what we should be concerned about is mode -> clock, 
> not the HDMI PHY clock. The HDMI PHY clock is something that the HDMI bridge or the HDMI PHY driver needs to pay attention to.
> 
> This patch works just because currently, on RK3576 and RK3588, the HDMI PHY PLL can be used as the dclk source for the vop.
> After correctly setting CMN_REG0086, it can precisely adjust the HDMI HPY PLL clock adjusted according to the bpc further to
> the frequency of mode->clock, and then use it as the dclk for the vop.
> However, we also need to be aware of the following situations:
> 
> 1) When we are using HDMI, we can still choose the system PLL instead of the HDMI PHY PLL as
>     the clock source for dclk. In this case, this patch will cause incorrect mode->clock.
> 2)  When we are using HDMI above the 4K60 mode(4K120), we can only use the system PLL instead
>      of the HDMIPHY PLL as the clock source for the vop dclk,  this patch will cause incorrect mode->clock.
> 3) For RK3576 and RK3588,  interfaces such as DP, eDP, and DSI also support 10-bit mode. 
>     However, in most cases, they will choose the system PLL as the vop dclk clock source,this patch will cause incorrect mode->clock.
> 4) There are also other platforms, such as RK3568, even for HDMI , it still uses the system PLL as the dclk clock source for vop.
>      this patch will cause incorrect mode->clock.

Oh, I wrongly assumed high color depth is not currently supported/in use for vop2.

In that case my suggestion below is actually a mandatory thing to do, as it should 
correctly reduce the scope to RK3576 & RK3588 only.

>>
>> Regardless, I should probably move this clock adjustment to the conditional
>> block handling DCLK source switch.
>>
>> [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/gpu/drm/display/drm_hdmi_state_helper.c?h=v6.16-rc7#n525
>> [2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/gpu/drm/display/drm_hdmi_state_helper.c?h=v6.16-rc7#n608
>> [3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c?h=v6.16-rc7#n1034