[PATCH 2/3] arm64: dts: s32g3: Fix whitespace issue in device tree

Dan Carpenter dan.carpenter at linaro.org
Wed Jul 16 15:46:31 PDT 2025


Checkpatch points out that this should use spaces instead of tabs.
"ERROR: code indent should use tabs where possible".

Reported-by: Xu Yang <xu.yang_2 at nxp.com>
Closes: https://lore.kernel.org/all/u7glt7mn33lbdeskbr4ily6tjjifvffy64llwpi5b2rrhx5tnv@y2h2y3oz3xc4/
Signed-off-by: Dan Carpenter <dan.carpenter at linaro.org>
---
 arch/arm64/boot/dts/freescale/s32g3.dtsi | 32 ++++++++++++------------
 1 file changed, 16 insertions(+), 16 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/s32g3.dtsi b/arch/arm64/boot/dts/freescale/s32g3.dtsi
index 68c11ebd405f..e80144e33efb 100644
--- a/arch/arm64/boot/dts/freescale/s32g3.dtsi
+++ b/arch/arm64/boot/dts/freescale/s32g3.dtsi
@@ -489,22 +489,22 @@ usbmisc: usbmisc at 44064200 {
 			reg = <0x44064200 0x200>;
 		};
 
-                usbotg: usb at 44064000 {
-                        compatible = "nxp,s32g3-usb", "nxp,s32g2-usb";
-                        reg = <0x44064000 0x200>;
-                        interrupt-parent = <&gic>;
-                        interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, /* OTG Core */
-                                     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>; /* OTG Wakeup */
-                        clocks = <&clks 94>, <&clks 95>;
-                        fsl,usbmisc = <&usbmisc 0>;
-                        ahb-burst-config = <0x3>;
-                        tx-burst-size-dword = <0x10>;
-                        rx-burst-size-dword = <0x10>;
-                        phy_type = "ulpi";
-                        dr_mode = "host";
-                        maximum-speed = "high-speed";
-                        status = "disabled";
-                };
+		usbotg: usb at 44064000 {
+			compatible = "nxp,s32g3-usb", "nxp,s32g2-usb";
+			reg = <0x44064000 0x200>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, /* OTG Core */
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>; /* OTG Wakeup */
+			clocks = <&clks 94>, <&clks 95>;
+			fsl,usbmisc = <&usbmisc 0>;
+			ahb-burst-config = <0x3>;
+			tx-burst-size-dword = <0x10>;
+			rx-burst-size-dword = <0x10>;
+			phy_type = "ulpi";
+			dr_mode = "host";
+			maximum-speed = "high-speed";
+			status = "disabled";
+		};
 
 		i2c0: i2c at 401e4000 {
 			compatible = "nxp,s32g3-i2c",
-- 
2.47.2




More information about the linux-arm-kernel mailing list