[PATCH v2 1/7] arm64: dts: ti: k3-j784s4-j742s2-main-common: add DSI & DSI PHY

[Jayesh Choudhary]

Hello Vignesh,

On 26/06/25 11:56, Vignesh Raghavendra wrote:
> Hi
> 
> On 24/06/25 13:56, Jayesh Choudhary wrote:
>> Add DT nodes for DPI to DSI Bridge and DSI Phy.
>> The DSI bridge is Cadence DSI and the PHY is a
>> Cadence DPHY with TI wrapper.
>>
>> Signed-off-by: Jayesh Choudhary <j-choudhary at ti.com>
>> ---
>>   .../dts/ti/k3-j784s4-j742s2-main-common.dtsi  | 37 +++++++++++++++++++
>>   1 file changed, 37 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
>> index 363d68fec387..2413c4913a8b 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
>> @@ -2517,6 +2517,43 @@ watchdog18: watchdog at 2550000 {
>>   		status = "reserved";
>>   	};
>>   
>> +	dphy_tx0: phy at 4480000 {
>> +		compatible = "ti,j721e-dphy";
>> +		reg = <0x0 0x04480000 0x0 0x1000>;
> 
> Follow the convention of the file. Use:
> 
> 		reg = <0x00 0x04480000 0x00 0x1000>;

Okay I will add padding.
Will add it to 4th field as well as I am seeing it in some
nodes:

reg = <0x00 0x04480000 0x00 0x00001000>;

> 
> Please fix throughout the series.


Okay.

> 
>> +		clocks = <&k3_clks 402 20>, <&k3_clks 402 3>;
>> +		clock-names = "psm", "pll_ref";
>> +		#phy-cells = <0>;
>> +		power-domains = <&k3_pds 402 TI_SCI_PD_EXCLUSIVE>;
>> +		assigned-clocks = <&k3_clks 402 3>;
>> +		assigned-clock-parents = <&k3_clks 402 4>;
>> +		assigned-clock-rates = <19200000>;
>> +		status = "disabled";
>> +	};
>> +
>> +	dsi0: dsi at 4800000 {
>> +		compatible = "ti,j721e-dsi";
>> +		reg = <0x0 0x04800000 0x0 0x100000>, <0x0 0x04710000 0x0 0x100>;
>> +		clocks = <&k3_clks 215 2>, <&k3_clks 215 5>;
>> +		clock-names = "dsi_p_clk", "dsi_sys_clk";
>> +		power-domains = <&k3_pds 215 TI_SCI_PD_EXCLUSIVE>;
> 
>> +		interrupt-parent = <&gic500>;
> 
> This is implied and can be dropped.

Will drop.

Warm Regards,
Jayesh

> 
>> +		interrupts = <GIC_SPI 600 IRQ_TYPE_LEVEL_HIGH>;
>> +		phys = <&dphy_tx0>;
>> +		phy-names = "dphy";
>> +		status = "disabled";
>> +
>> +		dsi0_ports: ports {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			port at 0 {
>> +				reg = <0>;
>> +			};
>> +			port at 1 {
>> +				reg = <1>;
>> +			};
>> +		};
>> +	};
>> +
>>   	mhdp: bridge at a000000 {
>>   		compatible = "ti,j721e-mhdp8546";
>>   		reg = <0x0 0xa000000 0x0 0x30a00>,
>