[PATCH v2 2/2] arm64: dts: ti: k3-am654-base-board: add boot phase tags
Bryan Brattlof
bb at ti.com
Thu Jul 10 07:39:00 PDT 2025
The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used in the bootloader for the
AM654 reference board.
UARTs used as a console, the SD and eMMC nodes along with the needed
regulators for UHS modes, and the needed nodes for OSPI boot are all
marked with 'bootph-all' to handle the various boot modes the board is
capable of
Signed-off-by: Bryan Brattlof <bb at ti.com>
---
arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 17 +++++++++++++++++
arch/arm64/boot/dts/ti/k3-am654-pcie-usb2.dtso | 1 +
arch/arm64/boot/dts/ti/k3-am654-pcie-usb3.dtso | 1 +
3 files changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index c30425960398ebb75ebda44726ed90cd78947d58..e589690c7c8213d5e4989942735fa53825e610f5 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -144,6 +144,7 @@ vtt_supply: regulator-3 {
regulator-boot-on;
vin-supply = <&vcc3v3_io>;
gpio = <&wkup_gpio0 28 GPIO_ACTIVE_HIGH>;
+ bootph-all;
};
};
@@ -155,12 +156,14 @@ AM65X_WKUP_IOPAD(0x00a4, PIN_OUTPUT, 0) /* (AB5) WKUP_UART0_TXD */
AM65X_WKUP_IOPAD(0x00c8, PIN_INPUT, 1) /* (AC2) WKUP_GPIO0_6.WKUP_UART0_CTSn */
AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT, 1) /* (AC1) WKUP_GPIO0_7.WKUP_UART0_RTSn */
>;
+ bootph-all;
};
ddr_vtt_pins_default: ddr-vtt-default-pins {
pinctrl-single,pins = <
AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7) /* WKUP_GPIO0_28 */
>;
+ bootph-all;
};
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
@@ -168,6 +171,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
AM65X_WKUP_IOPAD(0x00e0, PIN_INPUT, 0) /* (AC7) WKUP_I2C0_SCL */
AM65X_WKUP_IOPAD(0x00e4, PIN_INPUT, 0) /* (AD6) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
push_button_pins_default: push-button-default-pins {
@@ -191,6 +195,7 @@ AM65X_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* (R2) MCU_OSPI0_D6 */
AM65X_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* (R3) MCU_OSPI0_D7 */
AM65X_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* (R4) MCU_OSPI0_CSn0 */
>;
+ bootph-all;
};
wkup_pca554_default: wkup-pca554-default-pins {
@@ -206,6 +211,7 @@ AM65X_WKUP_IOPAD(0x0048, PIN_OUTPUT, 4) /* (P5) MCU_OSPI1_D2.MCU_UART0_TXD */
AM65X_WKUP_IOPAD(0x004C, PIN_INPUT, 4) /* (P1) MCU_OSPI1_D3.MCU_UART0_CTSn */
AM65X_WKUP_IOPAD(0x0054, PIN_OUTPUT, 4) /* (N3) MCU_OSPI1_CSn1.MCU_UART0_RTSn */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -248,6 +254,7 @@ AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0) /* (AE11) UART0_TXD */
AM65X_IOPAD(0x01ec, PIN_INPUT, 0) /* (AG11) UART0_CTSn */
AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0) /* (AD11) UART0_RTSn */
>;
+ bootph-all;
};
main_i2c2_pins_default: main-i2c2-default-pins {
@@ -281,6 +288,7 @@ AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */
AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP, 0) /* (A23) MMC0_SDCD */
AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */
>;
+ bootph-all;
};
main_mmc1_pins_default: main-mmc1-default-pins {
@@ -294,6 +302,7 @@ AM65X_IOPAD(0x02c4, PIN_INPUT_PULLUP, 0) /* (D27) MMC1_DAT3 */
AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP, 0) /* (B24) MMC1_SDCD */
AM65X_IOPAD(0x02e0, PIN_INPUT, 0) /* (C24) MMC1_SDWP */
>;
+ bootph-all;
};
usb1_pins_default: usb1-default-pins {
@@ -343,6 +352,7 @@ &main_uart0 {
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&wkup_i2c0 {
@@ -368,6 +378,7 @@ vdd_mpu: regulator at 60 {
ti,vsel0-state-high;
ti,vsel1-state-high;
ti,enable-vout-discharge;
+ bootph-all;
};
gpio at 38 {
@@ -456,6 +467,7 @@ &sdhci0 {
bus-width = <8>;
non-removable;
ti,driver-strength-ohm = <50>;
+ bootph-all;
};
/*
@@ -470,6 +482,7 @@ &sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&usb1 {
@@ -630,3 +643,7 @@ &cpsw_port1 {
&dss {
status = "disabled";
};
+
+&wkup_gpio0 {
+ bootph-all;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am654-pcie-usb2.dtso b/arch/arm64/boot/dts/ti/k3-am654-pcie-usb2.dtso
index c3cb752f8cd79459d6d321dfdf0644748514a48d..d04dd7a44008205301ea3fb3d0a883b6a6a2562b 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-pcie-usb2.dtso
+++ b/arch/arm64/boot/dts/ti/k3-am654-pcie-usb2.dtso
@@ -46,6 +46,7 @@ AM65X_IOPAD(0x02bc, PIN_OUTPUT, 0) /* (AD9) USB0_DRVVBUS */
&dwc3_0 {
status = "okay";
+ bootph-all;
};
&usb0_phy {
diff --git a/arch/arm64/boot/dts/ti/k3-am654-pcie-usb3.dtso b/arch/arm64/boot/dts/ti/k3-am654-pcie-usb3.dtso
index 333e423e8bb6b033f5f45c782ef0095d29983158..04393f21d712ebd95ce1a411e2ac13a56e63e57b 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-pcie-usb3.dtso
+++ b/arch/arm64/boot/dts/ti/k3-am654-pcie-usb3.dtso
@@ -45,6 +45,7 @@ &dwc3_0 {
<&k3_clks 151 8>; /* set PIPE3_TXB_CLK to WIZ8B2M4VSB */
phys = <&serdes0 PHY_TYPE_USB3 0>;
phy-names = "usb3-phy";
+ bootph-all;
};
&usb0 {
--
2.49.0
More information about the linux-arm-kernel
mailing list