[PATCH] arm64: dts: ti: k3-am62a7-sk: add boot phase tags

[Bryan Brattlof]

The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used during the early stages of
bootup by the bootloaders.

This includes the console UART along with the SD and eMMC nodes and its
required regulators for the 3v3 to 1v8 transition and the various nodes
for Ethernet booting.

Signed-off-by: Bryan Brattlof <bb at ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index f11284b3fe8e23b4c48d8d2f3a7202e80dc57370..bb565c52dc2c6365aac1e3a62461de4aef79c51b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -36,6 +36,7 @@ memory at 80000000 {
 		/* 4G RAM */
 		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
 		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+		bootph-all;
 	};
 
 	reserved-memory {
@@ -151,6 +152,7 @@ vdd_mmc1: regulator-3 {
 		regulator-boot-on;
 		enable-active-high;
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+		bootph-all;
 	};
 
 	vcc_3v3_sys: regulator-4 {
@@ -297,6 +299,7 @@ main_uart0_pins_default: main-uart0-default-pins {
 			AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (E14) UART0_RXD */
 			AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (D15) UART0_TXD */
 		>;
+		bootph-all;
 	};
 
 	main_uart1_pins_default: main-uart1-default-pins {
@@ -320,6 +323,7 @@ main_i2c1_pins_default: main-i2c1-default-pins {
 			AM62AX_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
 			AM62AX_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
 		>;
+		bootph-all;
 	};
 
 	main_i2c2_pins_default: main-i2c2-default-pins {
@@ -356,6 +360,7 @@ AM62AX_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
 			AM62AX_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
 			AM62AX_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
 		>;
+		bootph-all;
 	};
 
 	usr_led_pins_default: usr-led-default-pins {
@@ -375,6 +380,7 @@ main_mdio1_pins_default: main-mdio1-default-pins {
 			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
 			AM62AX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
 		>;
+		bootph-all;
 	};
 
 	main_rgmii1_pins_default: main-rgmii1-default-pins {
@@ -392,6 +398,7 @@ AM62AX_IOPAD(0x140, PIN_INPUT, 0) /* (AA17) RGMII1_TD3 */
 			AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
 			AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 		>;
+		bootph-all;
 	};
 
 	main_mcasp1_pins_default: main-mcasp1-default-pins {
@@ -572,6 +579,7 @@ exp1: gpio at 22 {
 		#interrupt-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+		bootph-all;
 
 		gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
 				   "BT_EN_SOC", "MMC1_SD_EN",
@@ -675,10 +683,12 @@ &sdhci1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	disable-wp;
+	bootph-all;
 };
 
 &main_gpio0 {
 	status = "okay";
+	bootph-all;
 };
 
 &main_gpio1 {
@@ -693,6 +703,7 @@ &main_uart0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
+	bootph-all;
 };
 
 /* Main UART1 is used for TIFS firmware logs */
@@ -737,12 +748,21 @@ &cpsw3g {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_rgmii1_pins_default>;
+
+	ethernet-ports {
+		bootph-all;
+	};
+};
+
+&phy_gmii_sel {
+	bootph-all;
 };
 
 &cpsw_port1 {
 	status = "okay";
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy0>;
+	bootph-all;
 };
 
 &cpsw_port2 {
@@ -759,6 +779,7 @@ cpsw3g_phy0: ethernet-phy at 0 {
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 		ti,min-output-impedance;
+		bootph-all;
 	};
 };
 

---
base-commit: 3b08f8a34a2061d89a2411d04a675b3860d4f9cc
change-id: 20250623-62a-uboot-cleanup-b80e6952f91d

Best regards,
-- 
Bryan Brattlof <bb at ti.com>