[PATCH v6 4/4] arm64: dts: ti: k3-am69-sk: Add bootph-all property to enable Ethernet boot

[Chintan Vankar]

Ethernet boot requires CPSW nodes to be present starting from R5 SPL
stage. Add bootph-all property to required nodes to enable Ethernet boot
for SK-AM69.

Reviewed-by: Siddharth Vadapalli <s-vadapalli at ti.com>
Signed-off-by: Chintan Vankar <c-vankar at ti.com>
---

Link to v5:
https://lore.kernel.org/r/20250708084252.1028191-5-c-vankar@ti.com/

Changes from v5 to v6:
- Added bootph-all property to cpsw_mac_syscon node.
- Corrected "bootph-all" which was misspelled in previous version.

 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index f28375629739..a09dcb812648 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -568,6 +568,7 @@ J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E38) MCU_RGMII1_TD3 */
 			J784S4_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (E36) MCU_RGMII1_TXC */
 			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (C38) MCU_RGMII1_TX_CTL */
 		>;
+		bootph-all;
 	};
 
 	mcu_mdio_pins_default: mcu-mdio-default-pins {
@@ -575,6 +576,7 @@ mcu_mdio_pins_default: mcu-mdio-default-pins {
 			J784S4_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */
 			J784S4_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */
 		>;
+		bootph-all;
 	};
 
 	mcu_rpi_hdr1_gpio0_pins_default: mcu-rpi-hdr1-gpio0-default-pins {
@@ -630,6 +632,14 @@ J784S4_WKUP_IOPAD(0x0, PIN_INPUT, 7) /* (M33) WKUP_GPIO0_49 */
 	};
 };
 
+&cpsw_mac_syscon {
+	bootph-all;
+};
+
+&phy_gmii_sel {
+	bootph-all;
+};
+
 &mailbox0_cluster0 {
 	status = "okay";
 	interrupts = <436>;
@@ -968,6 +978,7 @@ &mcu_cpsw {
 &davinci_mdio {
 	mcu_phy0: ethernet-phy at 0 {
 		reg = <0>;
+		bootph-all;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 		ti,min-output-impedance;
@@ -978,6 +989,7 @@ &mcu_cpsw_port1 {
 	status = "okay";
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&mcu_phy0>;
+	bootph-all;
 };
 
 &mcu_r5fss0_core0 {
-- 
2.34.1