[PATCH 8/9] arm64: dts: lx2160a-rdb: fully describe the two SFP+ cages

[Ioana Ciornei]

Describe the two SFP+ cages found on the LX2160ARDB board with their
respective I2C buses and GPIO lines.

Signed-off-by: Ioana Ciornei <ioana.ciornei at nxp.com>
---
 .../boot/dts/freescale/fsl-lx2160a-rdb.dts    | 45 +++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
index 8209dafd7768..762c38fc6fa0 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
@@ -31,6 +31,26 @@ sb_3v3: regulator-sb3v3 {
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&sfp2_i2c>;
+		maximum-power-milliwatt = <2000>;
+		tx-disable-gpios = <&sfp2_csr 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sfp2_csr 4 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&sfp2_csr 5 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfp2_csr 7 GPIO_ACTIVE_LOW>;
+	};
+
+	sfp3: sfp-3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&sfp3_i2c>;
+		maximum-power-milliwatt = <2000>;
+		tx-disable-gpios = <&sfp3_csr 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sfp3_csr 4 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&sfp3_csr 5 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfp3_csr 7 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &crypto {
@@ -236,6 +256,31 @@ temperature-sensor at 4d {
 				vcc-supply = <&sb_3v3>;
 			};
 		};
+
+		i2c at 7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+
+			i2c-mux at 75 {
+				compatible = "nxp,pca9547";
+				reg = <0x75>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sfp2_i2c: i2c at 4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+
+				sfp3_i2c: i2c at 5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+			};
+		};
 	};
 };
 
-- 
2.25.1