[PATCH v6 1/4] arm64: dts: ti: Add bootph property to nodes at source for am62a

[Paresh Bhagat]

Add bootph property directly into the original definitions of relevant
nodes (e.g., power domains, USB controllers, and other peripherals)
within their respective DTSI files (ex. main, mcu, and wakeup) for
am62a.

By defining bootph in the nodes source definitions instead of appending
it later in final DTS files, this change ensures that the property is
inherently present wherever the nodes are reused across derived device
trees.

Signed-off-by: Paresh Bhagat <p-bhagat at ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi   | 13 +++++++++++++
 arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi |  2 ++
 2 files changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
index 63e097ddf988..44e7e459f176 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
@@ -51,6 +51,7 @@ phy_gmii_sel: phy at 4044 {
 			compatible = "ti,am654-phy-gmii-sel";
 			reg = <0x4044 0x8>;
 			#phy-cells = <1>;
+			bootph-all;
 		};
 
 		epwm_tbclk: clock-controller at 4130 {
@@ -96,6 +97,7 @@ secure_proxy_main: mailbox at 4d000000 {
 			#mbox-cells = <1>;
 			interrupt-names = "rx_012";
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			bootph-all;
 		};
 
 		inta_main_dmss: interrupt-controller at 48000000 {
@@ -131,6 +133,7 @@ main_bcdma: dma-controller at 485c0100 {
 			ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
 			ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
 			ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+			bootph-all;
 		};
 
 		main_pktdma: dma-controller at 485c0000 {
@@ -147,6 +150,8 @@ main_pktdma: dma-controller at 485c0000 {
 				    "ring", "tchan", "rchan", "rflow";
 			msi-parent = <&inta_main_dmss>;
 			#dma-cells = <2>;
+			bootph-all;
+
 			ti,sci = <&dmsc>;
 			ti,sci-dev-id = <30>;
 			ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
@@ -220,16 +225,19 @@ dmsc: system-controller at 44043000 {
 		k3_pds: power-controller {
 			compatible = "ti,sci-pm-domain";
 			#power-domain-cells = <2>;
+			bootph-all;
 		};
 
 		k3_clks: clock-controller {
 			compatible = "ti,k2g-sci-clk";
 			#clock-cells = <2>;
+			bootph-all;
 		};
 
 		k3_reset: reset-controller {
 			compatible = "ti,sci-reset";
 			#reset-cells = <2>;
+			bootph-all;
 		};
 	};
 
@@ -254,6 +262,7 @@ secure_proxy_sa3: mailbox at 43600000 {
 		 * firmware on non-MPU processors
 		 */
 		status = "disabled";
+		bootph-all;
 	};
 
 	main_pmx0: pinctrl at f4000 {
@@ -282,6 +291,7 @@ main_timer0: timer at 2400000 {
 		assigned-clock-parents = <&k3_clks 36 3>;
 		power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
 		ti,timer-pwm;
+		bootph-all;
 	};
 
 	main_timer1: timer at 2410000 {
@@ -651,6 +661,7 @@ usb0: usb at 31000000 {
 			interrupt-names = "host", "peripheral";
 			maximum-speed = "high-speed";
 			dr_mode = "otg";
+			bootph-all;
 			snps,usb2-gadget-lpm-disable;
 			snps,usb2-lpm-disable;
 		};
@@ -745,6 +756,7 @@ cpsw_port1: port at 1 {
 				phys = <&phy_gmii_sel 1>;
 				mac-address = [00 00 00 00 00 00];
 				ti,syscon-efuse = <&cpsw_mac_syscon 0x0>;
+				bootph-all;
 			};
 
 			cpsw_port2: port at 2 {
@@ -764,6 +776,7 @@ cpsw3g_mdio: mdio at f00 {
 			clocks = <&k3_clks 13 0>;
 			clock-names = "fck";
 			bus_freq = <1000000>;
+			bootph-all;
 		};
 
 		cpts at 3d000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
index 259ae6ebbfb5..9ef1c829a9df 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
@@ -17,6 +17,7 @@ wkup_conf: bus at 43000000 {
 		chipid: chipid at 14 {
 			compatible = "ti,am654-chipid";
 			reg = <0x14 0x4>;
+			bootph-all;
 		};
 
 		opp_efuse_table: syscon at 18 {
@@ -67,6 +68,7 @@ wkup_uart0: serial at 0 {
 			reg = <0 0x100>;
 			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
+			bootph-pre-ram;
 	       };
 	};
 
-- 
2.34.1