[PATCH] arm64: dts: renesas: r8a779f0: Disable rswitch ports by default

[Geert Uytterhoeven]

The Renesas Ethernet Switch has three independent ports.  Each port can
act as a separate interface, and can be enabled or disabled
independently.  Currently all ports are enabled by default, hence board
DTS files that enable the switch must disable all unused ports
explicitly.

Disable all ports by default, and explicitly enable ports that are used,
next to their configuration.

Signed-off-by: Geert Uytterhoeven <geert+renesas at glider.be>
---
This is similar to how Ethernet switch ports are handled on RZ/N1D, and
CAN-FD channels on R-Car Gen3/4.

If accepted, I'm wondering if I should move it forward, before "[PATCH
3/5] arm64: dts: renesas: s4sk: Access rswitch ports via phandles"[1],
which would become slightly simpler.

[1] https://lore.kernel.org/all/20250118111344.361617-3-marek.vasut+renesas@mailbox.org
---
 arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi | 3 +++
 arch/arm64/boot/dts/renesas/r8a779f0.dtsi                 | 3 +++
 arch/arm64/boot/dts/renesas/r8a779f4-s4sk.dts             | 6 ++----
 3 files changed, 8 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi b/arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi
index 892729786d00b36e..ad2b0398d35431a1 100644
--- a/arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi
@@ -57,6 +57,7 @@ &rswitch_port0 {
 	phy-handle = <&u101>;
 	phy-mode = "sgmii";
 	phys = <&eth_serdes 0>;
+	status = "okay";
 
 	mdio {
 		#address-cells = <1>;
@@ -75,6 +76,7 @@ &rswitch_port1 {
 	phy-handle = <&u201>;
 	phy-mode = "sgmii";
 	phys = <&eth_serdes 1>;
+	status = "okay";
 
 	mdio {
 		#address-cells = <1>;
@@ -93,6 +95,7 @@ &rswitch_port2 {
 	phy-handle = <&u301>;
 	phy-mode = "sgmii";
 	phys = <&eth_serdes 2>;
+	status = "okay";
 
 	mdio {
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/renesas/r8a779f0.dtsi b/arch/arm64/boot/dts/renesas/r8a779f0.dtsi
index 840ba73c03f1b6f4..06be9f7720d64179 100644
--- a/arch/arm64/boot/dts/renesas/r8a779f0.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779f0.dtsi
@@ -989,14 +989,17 @@ ethernet-ports {
 				rswitch_port0: port at 0 {
 					reg = <0>;
 					phys = <&eth_serdes 0>;
+					status = "disabled";
 				};
 				rswitch_port1: port at 1 {
 					reg = <1>;
 					phys = <&eth_serdes 1>;
+					status = "disabled";
 				};
 				rswitch_port2: port at 2 {
 					reg = <2>;
 					phys = <&eth_serdes 2>;
+					status = "disabled";
 				};
 			};
 		};
diff --git a/arch/arm64/boot/dts/renesas/r8a779f4-s4sk.dts b/arch/arm64/boot/dts/renesas/r8a779f4-s4sk.dts
index 24ecdf6e8476a945..df652e7b85c95ebe 100644
--- a/arch/arm64/boot/dts/renesas/r8a779f4-s4sk.dts
+++ b/arch/arm64/boot/dts/renesas/r8a779f4-s4sk.dts
@@ -187,6 +187,7 @@ &rswitch_port0 {
 	phy-handle = <&ic99>;
 	phy-mode = "sgmii";
 	phys = <&eth_serdes 0>;
+	status = "okay";
 
 	mdio {
 		#address-cells = <1>;
@@ -205,6 +206,7 @@ &rswitch_port1 {
 	phy-handle = <&ic102>;
 	phy-mode = "sgmii";
 	phys = <&eth_serdes 1>;
+	status = "okay";
 
 	mdio {
 		#address-cells = <1>;
@@ -218,10 +220,6 @@ ic102: ethernet-phy at 2 {
 	};
 };
 
-&rswitch_port2 {
-	status = "disabled";
-};
-
 &rwdt {
 	timeout-sec = <60>;
 	status = "okay";
-- 
2.43.0