[PATCH v3 2/4] net: stmmac: dwmac-qcom-ethqos: Mask PHY mode if configured with rgmii-id
Yijie Yang
quic_yijiyang at quicinc.com
Wed Jan 22 01:46:47 PST 2025
On 2025-01-21 21:17, Maxime Chevallier wrote:
> Hi,
>
> On Tue, 21 Jan 2025 15:54:54 +0800
> Yijie Yang <quic_yijiyang at quicinc.com> wrote:
>
>> The Qualcomm board always chooses the MAC to provide the delay instead of
>> the PHY, which is completely opposite to the suggestion of the Linux
>> kernel. The usage of phy-mode in legacy DTS was also incorrect. Change the
>> phy_mode passed from the DTS to the driver from PHY_INTERFACE_MODE_RGMII_ID
>> to PHY_INTERFACE_MODE_RGMII to ensure correct operation and adherence to
>> the definition.
>> To address the ABI compatibility issue between the kernel and DTS caused by
>> this change, handle the compatible string 'qcom,qcs404-evb-4000' in the
>> code, as it is the only legacy board that mistakenly uses the 'rgmii'
>> phy-mode.
>>
>> Signed-off-by: Yijie Yang <quic_yijiyang at quicinc.com>
>> ---
>> .../net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 18 +++++++++++++-----
>> 1 file changed, 13 insertions(+), 5 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
>> index 2a5b38723635b5ef9233ca4709e99dd5ddf06b77..e228a62723e221d58d8c4f104109e0dcf682d06d 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
>> @@ -401,14 +401,11 @@ static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
>> static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
>> {
>> struct device *dev = ðqos->pdev->dev;
>> - int phase_shift;
>> + int phase_shift = 0;
>> int loopback;
>>
>> /* Determine if the PHY adds a 2 ns TX delay or the MAC handles it */
>> - if (ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_ID ||
>> - ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_TXID)
>> - phase_shift = 0;
>> - else
>> + if (ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_ID)
>> phase_shift = RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN;
>
> So this looks like a driver modification to deal with errors in
> devicetree, and these modifications don't seem to be correct.
>
> You should set RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN (i.e. adding a delay
> n the TX line) when the PHY does not add internal delays on that line
> (so, when the mode is rgmii or rgmii-rxid. The previous logic looks
> correct in that regard.
>
> Can you elaborate a bit more on the issue you are seeing ? On what
> hardware is this happening ? What's the RGMII setup used (i.e. which
> PHY, which mode, is there any delay lines on the PCB ?)
As discussed following the first patch, the previous method of using
'rgmii' in DTS while adding delay via the MAC was incorrect. We need to
correct this misuse in both the DTS and the driver. For new boards, the
phy-mode should be 'rgmii-id', while legacy boards will remain 'rgmii'.
Both configurations will still enable
RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN and allow the MAC to add the delay,
ensuring the behavior remains consistent before and after the change.
>
> Thanks,
>
> Maxime
--
Best Regards,
Yijie
More information about the linux-arm-kernel
mailing list