[PATCH v3 2/2] ARM: dts: socfpga: Add basic support for Terrasic's de10-nano

[Uwe Kleine-König]

This dts is enough to make the board boot to Linux with the rootfs on
a micro SD card.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig at baylibre.com>
---
 arch/arm/boot/dts/intel/socfpga/Makefile      |  1 +
 .../socfpga/socfpga_cyclone5_de10nano.dts     | 95 +++++++++++++++++++
 2 files changed, 96 insertions(+)
 create mode 100644 arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts

diff --git a/arch/arm/boot/dts/intel/socfpga/Makefile b/arch/arm/boot/dts/intel/socfpga/Makefile
index c467828aeb4b..7f69a0355ea5 100644
--- a/arch/arm/boot/dts/intel/socfpga/Makefile
+++ b/arch/arm/boot/dts/intel/socfpga/Makefile
@@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
 	socfpga_cyclone5_mcvevk.dtb \
 	socfpga_cyclone5_socdk.dtb \
 	socfpga_cyclone5_de0_nano_soc.dtb \
+	socfpga_cyclone5_de10nano.dtb \
 	socfpga_cyclone5_sockit.dtb \
 	socfpga_cyclone5_socrates.dtb \
 	socfpga_cyclone5_sodia.dtb \
diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts
new file mode 100644
index 000000000000..ec25106caacf
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017, Intel Corporation
+ *
+ * based on socfpga_cyclone5_de0_nano_soc.dts
+ */
+/dts-v1/;
+
+#include "socfpga_cyclone5.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Terasic DE10-Nano";
+	compatible = "terasic,de10-nano", "altr,socfpga-cyclone5", "altr,socfpga";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory at 0 {
+		/* 1 GiB */
+		device_type = "memory";
+		reg = <0x0 0x40000000>;
+	};
+
+	soc {
+		fpga: bus at ff200000 {
+			compatible = "simple-bus";
+			reg = <0xff200000 0x00200000>;
+			ranges = <0x00000000 0xff200000 0x00200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/*
+			 * Here the devices will appear if an FPGA image is
+			 * loaded. Their description is expected to be added
+			 * using a device tree overlay that matches the image.
+			 */
+		};
+	};
+};
+
+&gmac1 {
+	/* Uses a KSZ9031RNX phy */
+	phy-mode = "rgmii-id";
+	rxd0-skew-ps = <420>;
+	rxd1-skew-ps = <420>;
+	rxd2-skew-ps = <420>;
+	rxd3-skew-ps = <420>;
+	txen-skew-ps = <0>;
+	rxdv-skew-ps = <420>;
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	accelerometer at 53 {
+		compatible = "adi,adxl345";
+		reg = <0x53>;
+		/* HPS_GSENSOR_INT is routed to UART0_RX/CAN0_RX/SPIM0_SS1/HPS_GPIO61 */
+		interrupt-parent = <&portc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "INT1";
+	};
+};
+
+&mmc0 {
+	/* micro SD card socket J11 */
+	status = "okay";
+};
+
+&uart0 {
+	/*
+	 * Accessible via USB (FT232R) on Mini-USB plug J4
+	 * RX = TRACE_D0/SPIS0_CLK/UART0_RX/HPS_GPIO49
+	 * TX = TRACE_D1/SPIS0_MOSI/UART0_TX/HPS_GPIO50
+	 * no handshaking lines
+	 */
+	clock-frequency = <100000000>;
+};
-- 
2.47.1