[PATCH v3 2/2] arm64: dts: rockchip: Add Radxa ROCK 4D device tree

[Heiko Stübner]

Hi Detlev,

all the style nitpick I'd changed myself, but the cpu-supplies did throw me
off, see below.


Am Freitag, 14. Februar 2025, 16:19:34 MEZ schrieb Detlev Casanova:
> diff --git a/arch/arm64/boot/dts/rockchip/rk3576-rock-4d.dts b/arch/arm64/boot/dts/rockchip/rk3576-rock-4d.dts
> new file mode 100644
> index 0000000000000..822abb82fae40
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3576-rock-4d.dts
> @@ -0,0 +1,650 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2024 Radxa Computer (Shenzhen) Co., Ltd.
> + *

empty comment line can probably go away

> +	vcc_12v0_dcin: regulator-vcc-12v0-dcin {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_12v0_dcin";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +	};
> +
> +	vcc_5v0_sys: regulator-vcc-5v0-sys {

alphabetical sorting, by node-name please, so
regulator-vcc-3v3* comes before regulator-vcc-5v0* etc

Goes for all regulator-* nodes of course.

> +	vcc_3v3_pcie: regulator-vcc-3v3-pcie {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_3v3_pcie";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +		gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
> +		startup-delay-us = <5000>;
> +		vin-supply = <&vcc_5v0_sys>;
> +	};
> +
> +	vcc_5v0_host: regulator-vcc-5v0-host {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_host";
> +		regulator-boot-on;
> +		regulator-always-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
> +		vin-supply = <&vcc_5v0_device>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_host_pwren>;

both of the above, alphabetical sorting of properties please

> +	};
> +};
> +
> +&cpu_l0 {
> +	cpu-supply = <&vdd_cpu_lit_s0>;
> +};

What happened to the supplies of the other cores?
cpu_l1 - cpu_l3 probably need the same reference as above.

Who is powering the cpu_b* cores?


> +&i2c1 {
> +	status = "okay";
> +
> +	pmic at 23 {
> +		compatible = "rockchip,rk806";
> +		reg = <0x23>;
> +
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_pins
> +			     &rk806_dvs1_null
> +			     &rk806_dvs2_null
> +			     &rk806_dvs3_null>;
> +
> +		system-power-controller;
> +
> +		vcc1-supply = <&vcc_5v0_sys>;
> +		vcc2-supply = <&vcc_5v0_sys>;
> +		vcc3-supply = <&vcc_5v0_sys>;
> +		vcc4-supply = <&vcc_5v0_sys>;
> +		vcc5-supply = <&vcc_5v0_sys>;
> +		vcc6-supply = <&vcc_5v0_sys>;
> +		vcc7-supply = <&vcc_5v0_sys>;
> +		vcc8-supply = <&vcc_5v0_sys>;
> +		vcc9-supply = <&vcc_5v0_sys>;
> +		vcc10-supply = <&vcc_5v0_sys>;
> +		vcc11-supply = <&vcc_2v0_pldo_s3>;
> +		vcc12-supply = <&vcc_5v0_sys>;
> +		vcc13-supply = <&vcc_1v1_nldo_s3>;
> +		vcc14-supply = <&vcc_1v1_nldo_s3>;
> +		vcca-supply = <&vcc_5v0_sys>;
> +
> +		gpio-controller;
> +		#gpio-cells = <2>;

alphabetical sorting ... gpio* farther up please.


> +&uart0 {
> +	pinctrl-0 = <&uart0m0_xfer>;
> +	status = "okay";
> +};
> +
> +&combphy1_psu {
> +	status = "okay";
> +};

phandles also sorted alphabetical please

> +
> +&u2phy0 {
> +	status = "okay";
> +};
> +
> +&u2phy1 {
> +	status = "okay";
> +};
> +
> +&usb_drd1_dwc3 {
> +	dr_mode = "host";
> +	status = "okay";
> +};

Thanks a lot
Heiko