[PATCH 08/10] arm64: dts: st: introduce stm32mp21 SoCs family
Amelie Delaunay
amelie.delaunay at foss.st.com
Fri Feb 14 07:18:31 PST 2025
On 2/13/25 10:02, Krzysztof Kozlowski wrote:
> On Mon, Feb 10, 2025 at 04:21:02PM +0100, Amelie Delaunay wrote:
>> From: Alexandre Torgue <alexandre.torgue at foss.st.com>
>>
>> STM32MP21 family is composed of 3 SoCs defined as following:
>>
>> -STM32MP211: common part composed of 1*Cortex-A35, common peripherals
>> like SDMMC, UART, SPI, I2C, parallel display, 1*ETH ...
>>
>> -STM32MP213: STM32MP211 + a second ETH, CAN-FD.
>>
>> -STM32MP215: STM32MP213 + Display and CSI2.
>>
>> A second diversity layer exists for security features/ A35 frequency:
>> -STM32MP21xY, "Y" gives information:
>> -Y = A means A35 at 1.2GHz + no cryp IP and no secure boot.
>> -Y = C means A35 at 1.2GHz + cryp IP and secure boot.
>> -Y = D means A35 at 1.5GHz + no cryp IP and no secure boot.
>> -Y = F means A35 at 1.5GHz + cryp IP and secure boot.
>>
>> Signed-off-by: Alexandre Torgue <alexandre.torgue at foss.st.com>
>> Signed-off-by: Amelie Delaunay <amelie.delaunay at foss.st.com>
>> ---
>> arch/arm64/boot/dts/st/stm32mp211.dtsi | 130 ++++++++++++++++++++++++++++++++
>> arch/arm64/boot/dts/st/stm32mp213.dtsi | 9 +++
>> arch/arm64/boot/dts/st/stm32mp215.dtsi | 9 +++
>> arch/arm64/boot/dts/st/stm32mp21xc.dtsi | 8 ++
>> arch/arm64/boot/dts/st/stm32mp21xf.dtsi | 8 ++
>> 5 files changed, 164 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/st/stm32mp211.dtsi b/arch/arm64/boot/dts/st/stm32mp211.dtsi
>> new file mode 100644
>> index 0000000000000000000000000000000000000000..d384359e0ea16e2593795ff48d4a699324c8ca75
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/st/stm32mp211.dtsi
>> @@ -0,0 +1,130 @@
>> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
>> +/*
>> + * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
>> + * Author: Alexandre Torgue <alexandre.torgue at foss.st.com> for STMicroelectronics.
>> + */
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +
>> +/ {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu0: cpu at 0 {
>> + compatible = "arm,cortex-a35";
>> + device_type = "cpu";
>> + reg = <0>;
>> + enable-method = "psci";
>> + };
>> + };
>> +
>> + arm-pmu {
>> + compatible = "arm,cortex-a35-pmu";
>> + interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-affinity = <&cpu0>;
>> + interrupt-parent = <&intc>;
>> + };
>> +
>> + arm_wdt: watchdog {
>> + compatible = "arm,smc-wdt";
>> + arm,smc-id = <0xbc000000>;
>> + status = "disabled";
>> + };
>> +
>> + clocks {
>> + ck_flexgen_08: ck-flexgen-08 {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <64000000>;
>> + };
>> +
>> + ck_flexgen_51: ck-flexgen-51 {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <200000000>;
>> + };
>> + };
>> +
>> + firmware {
>> + optee {
>> + compatible = "linaro,optee-tz";
>> + method = "smc";
>> + };
>> +
>> + scmi: scmi {
>> + compatible = "linaro,scmi-optee";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + linaro,optee-channel-id = <0>;
>> +
>> + scmi_clk: protocol at 14 {
>> + reg = <0x14>;
>> + #clock-cells = <1>;
>> + };
>> +
>> + scmi_reset: protocol at 16 {
>> + reg = <0x16>;
>> + #reset-cells = <1>;
>> + };
>> + };
>> + };
>> +
>> + intc: interrupt-controller at 4ac00000 {
>
> MMIO nodes belong to the soc.
>
Indeed.
>> + compatible = "arm,cortex-a7-gic";
>> + #interrupt-cells = <3>;
>> + interrupt-controller;
>> + reg = <0x0 0x4ac10000 0x0 0x1000>,
>> + <0x0 0x4ac20000 0x0 0x2000>,
>> + <0x0 0x4ac40000 0x0 0x2000>,
>> + <0x0 0x4ac60000 0x0 0x2000>;
>> + };
>> +
>> + psci {
>> + compatible = "arm,psci-1.0";
>> + method = "smc";
>> + };
>> +
>> + timer {
>> + compatible = "arm,armv8-timer";
>> + interrupt-parent = <&intc>;
>> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
>> + arm,no-tick-in-suspend;
>> + };
>> +
>> + soc at 0 {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <2>;
>> + interrupt-parent = <&intc>;
>> + ranges = <0x0 0x0 0x0 0x0 0x80000000>;
>
> ranges is the second property. See DTS coding style.
>
Ok.
>> + dma-ranges = <0x0 0x0 0x80000000 0x1 0x0>;
>> +
>> + rifsc: bus at 42080000 {
>> + compatible = "simple-bus";
>> + reg = <0x42080000 0x0 0x1000>;
>> + #address-cells = <1>;
>> + #size-cells = <2>;
>> + ranges;
>
> and here is third.
>
>> + dma-ranges;
>> +
>> + usart2: serial at 400e0000 {
>
> Although addresses seem wrong. How bus could start at 0x4208 but device
> at 0x400e?
>
>> + compatible = "st,stm32h7-uart";
>> + reg = <0x400e0000 0x0 0x400>;
>> + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ck_flexgen_08>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + syscfg: syscon at 44230000 {
>> + compatible = "st,stm32mp25-syscfg", "syscon";
>
> Which soc is this? DTSI says stm32mp211, commit STM32MP21, but
> compatible xxx25?
>
Looks like a new compatible is needed, and I guess it is also true for
stm32mp231.
>> + reg = <0x44230000 0x0 0x10000>;
>> + };
>> + };
>> +};
>> diff --git a/arch/arm64/boot/dts/st/stm32mp213.dtsi b/arch/arm64/boot/dts/st/stm32mp213.dtsi
>> new file mode 100644
>> index 0000000000000000000000000000000000000000..22cdedd9abbf4efac2334d497618daa6cc76727b
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/st/stm32mp213.dtsi
>> @@ -0,0 +1,9 @@
>> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
>> +/*
>> + * Copyright (C) STMicroelectronics 2024 - All Rights Reserved
>> + * Author: Alexandre Torgue <alexandre.torgue at foss.st.com> for STMicroelectronics.
>> + */
>> +#include "stm32mp211.dtsi"
>> +
>> +/ {
>> +};
>> diff --git a/arch/arm64/boot/dts/st/stm32mp215.dtsi b/arch/arm64/boot/dts/st/stm32mp215.dtsi
>> new file mode 100644
>> index 0000000000000000000000000000000000000000..d2c63e92b3cc15ec64898374fd2e745a9c71eb6d
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/st/stm32mp215.dtsi
>> @@ -0,0 +1,9 @@
>> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
>> +/*
>> + * Copyright (C) STMicroelectronics 2024 - All Rights Reserved
>> + * Author: Alexandre Torgue <alexandre.torgue at foss.st.com> for STMicroelectronics.
>> + */
>> +#include "stm32mp213.dtsi"
>> +
>> +/ {
>> +};
>
> What is the point of this file exactly?
>
Skeleton file for upcoming second ethernet and can-fd peripherals, not
available on stm32mp211.
>> diff --git a/arch/arm64/boot/dts/st/stm32mp21xc.dtsi b/arch/arm64/boot/dts/st/stm32mp21xc.dtsi
>> new file mode 100644
>> index 0000000000000000000000000000000000000000..39507a7564c8488647a3276eb227eb5f446359e6
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/st/stm32mp21xc.dtsi
>> @@ -0,0 +1,8 @@
>> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
>> +/*
>> + * Copyright (C) STMicroelectronics 2024 - All Rights Reserved
>> + * Author: Alexandre Torgue <alexandre.torgue at foss.st.com> for STMicroelectronics.
>> + */
>> +
>> +/ {
>> +};
>
> And this and others.
>
Skeleton file for upcoming cryptographic support, not available on
stm32mp21xa and stm32mp21xd.
As said previously, same split is used on other STM32 MPUs.
Regards,
Amelie
More information about the linux-arm-kernel
mailing list