[PATCH 08/12] arm64: dts: mediatek: mt8395-radxa-nio-12l: Enable HDMI output

[Louis-Alexis Eyraud]

From: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>

Add a definition for the on-board HDMI connector, enable and add
the relevant configuration for the HDMI PHY and controller, and
define the pins used by those.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud at collabora.com>
---
 .../boot/dts/mediatek/mt8395-radxa-nio-12l.dts     | 142 +++++++++++++++++++++
 1 file changed, 142 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts b/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
index d32f973f5e0528bc3233ff01f029006dbe6ef894..b0e18876bd5d2341c6f17f47e9f11433be807ccd 100644
--- a/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
@@ -37,6 +37,20 @@ chosen {
 		stdout-path = "serial0:921600n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+		ddc-i2c-bus = <&hdmitx_ddc>;
+		hdmi-pwr-supply = <&hdmi_phy>;
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi0_out>;
+			};
+		};
+	};
+
 	firmware {
 		optee {
 			compatible = "linaro,optee-tz";
@@ -245,6 +259,18 @@ port at 1 {
 	};
 };
 
+&dpi1 {
+	status = "okay";
+};
+
+&dpi1_in {
+	remote-endpoint = <&merge5_out>;
+};
+
+&dpi1_out {
+	remote-endpoint = <&hdmi0_in>;
+};
+
 &eth {
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&rgmii_phy>;
@@ -265,11 +291,61 @@ rgmii_phy: ethernet-phy at 1 {
 	};
 };
 
+&ethdr0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			ethdr0_in: endpoint at 1 {
+				reg = <1>;
+				remote-endpoint = <&vdosys1_ep_ext>;
+			};
+		};
+
+		port at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			ethdr0_out: endpoint at 1 {
+				reg = <1>;
+				remote-endpoint = <&merge5_in>;
+			};
+		};
+	};
+};
+
 &gpu {
 	mali-supply = <&mt6315_7_vbuck1>;
 	status = "okay";
 };
 
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_pins>;
+	status = "okay";
+};
+
+&hdmi0_in {
+	remote-endpoint = <&dpi1_out>;
+};
+
+&hdmi0_out {
+	remote-endpoint = <&hdmi_connector_in>;
+};
+
+&hdmi_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_vreg_pins>;
+
+	status = "okay";
+};
+
 &i2c2 {
 	clock-frequency = <400000>;
 	pinctrl-0 = <&i2c2_pins>;
@@ -448,6 +524,35 @@ typec_con_mux: endpoint {
 	};
 };
 
+&merge5 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			merge5_in: endpoint at 1 {
+				reg = <1>;
+				remote-endpoint = <&ethdr0_out>;
+			};
+		};
+
+		port at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			merge5_out: endpoint at 1 {
+				reg = <1>;
+				remote-endpoint = <&dpi1_in>;
+			};
+		};
+	};
+};
+
 &mfg0 {
 	domain-supply = <&mt6315_7_vbuck1>;
 };
@@ -647,6 +752,31 @@ pins {
 		};
 	};
 
+	hdmi_vreg_pins: hdmi-vreg-pins {
+		pins-pwr {
+			pinmux = <PINMUX_GPIO31__FUNC_HDMITX20_PWR5V>;
+			bias-disable;
+		};
+	};
+
+	hdmi_pins: hdmi-pins {
+		pins-hotplug {
+			pinmux = <PINMUX_GPIO32__FUNC_HDMITX20_HTPLG>;
+			bias-pull-down;
+		};
+
+		pins-ddc {
+			pinmux = <PINMUX_GPIO34__FUNC_HDMITX20_SCL>,
+				 <PINMUX_GPIO35__FUNC_HDMITX20_SDA>;
+			drive-strength = <10>;
+		};
+
+		pins-cec {
+			pinmux = <PINMUX_GPIO33__FUNC_HDMITX20_CEC>;
+			bias-disable;
+		};
+	};
+
 	i2c2_pins: i2c2-pins {
 		pins-bus {
 			pinmux = <PINMUX_GPIO12__FUNC_SDA2>,
@@ -1058,6 +1188,18 @@ &ssusb2 {
 	status = "okay";
 };
 
+&vdosys1 {
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdosys1_ep_ext: endpoint at 1 {
+			reg = <1>;
+			remote-endpoint = <&ethdr0_in>;
+		};
+	};
+};
+
 &xhci0 {
 	vbus-supply = <&otg_vbus_regulator>;
 	status = "okay";

-- 
2.52.0