[PATCH 2/2] arm64: dts: imx93-phyboard-segin: Add peb-av-02 overlay
Primoz Fiser
primoz.fiser at norik.com
Wed Dec 3 00:34:43 PST 2025
Hi Marco,
On 2. 12. 25 14:44, Marco Felsch wrote:
> From: Andrej Picej <andrej.picej at norik.com>
>
> Add overlay for Audio-Video module PEB-AV-02. Add support for panel
> display, capacitive touchscreen and backlight.
>
> For now the backlight is configured as a GPIO, brightness of the display
> can not be set. When the FLEXIO PWM driver is available this should be
> switched to PWM backlight driver.
>
> Signed-off-by: Andrej Picej <andrej.picej at norik.com>
> [rework commit message, use local regulator, remove compatible]
> Signed-off-by: Primoz Fiser <primoz.fiser at norik.com>
> Signed-off-by: Christian Hemp <c.hemp at phytec.de>
> [m.felsch at pengutronix.de: cleanup downstream commit]
> Signed-off-by: Marco Felsch <m.felsch at pengutronix.de>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 2 +
> .../freescale/imx93-phyboard-segin-peb-av-02.dtso | 135 +++++++++++++++++++++
> 2 files changed, 137 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 525ef180481d331e9c4decd092b7b831c497b67e..27e27ac29e82bc0692e86c2ba15c240dc9fbe1c6 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -357,10 +357,12 @@ dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-nash.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin.dtb
>
> imx93-phyboard-nash-peb-wlbt-07-dtbs += imx93-phyboard-nash.dtb imx93-phyboard-nash-peb-wlbt-07.dtbo
> +imx93-phyboard-segin-peb-av-02-dtbs += imx93-phyboard-segin.dtb imx93-phyboard-segin-peb-av-02.dtbo
> imx93-phyboard-segin-peb-eval-01-dtbs += imx93-phyboard-segin.dtb imx93-phyboard-segin-peb-eval-01.dtbo
> imx93-phyboard-segin-peb-wlbt-05-dtbs += imx93-phyboard-segin.dtb imx93-phyboard-segin-peb-wlbt-05.dtbo
> imx93-phycore-rpmsg-dtbs += imx93-phyboard-nash.dtb imx93-phyboard-segin.dtb imx93-phycore-rpmsg.dtbo
> dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-nash-peb-wlbt-07.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin-peb-av-02.dtb
Here you need to rebase since new commits on linux-next.
> dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin-peb-eval-01.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin-peb-wlbt-05.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-phycore-rpmsg.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phyboard-segin-peb-av-02.dtso b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin-peb-av-02.dtso
> new file mode 100644
> index 0000000000000000000000000000000000000000..2e7074e402dc8fdeb1568d4f2d4960431e972501
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin-peb-av-02.dtso
> @@ -0,0 +1,135 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2025 PHYTEC Messtechnik GmbH
> + * Copyright (C) 2025 Pengutronix
> + *
> + * Author: Andrej Picej <andrej.picej at norik.com>
> + * Author: Marco Felsch <kernel at pengutronix.de>
> + */
> +
> +#include <dt-bindings/clock/imx93-clock.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "imx93-pinfunc.h"
> +
> +/dts-v1/;
> +/plugin/;
> +
> +&{/} {
> + /* TODO: Convert to PWM backlight once the FlexIO PWM is supported */
> + backlight: backlight {
> + compatible = "gpio-backlight";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight>;
> + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + };
> +
> + panel {
> + compatible = "edt,etm0700g0edh6";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_panel>;
> +
> + backlight = <&backlight>;
> + enable-gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_x71_vcc_3v3>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&dpi_to_panel>;
> + };
> + };
> + };
> +
> + reg_x71_vcc_3v3: regulator-x71-vcc-3v3 {
I just checked the schematics.
Can we rename this to reg_vcc_3v3_con in v2 maybe?
> + compatible = "regulator-fixed";
> + regulator-name = "X71-VCC3V3";
And this to "VCC3V3_CON"?
The reasoning behind is that "X71-VCC3V3" voltage doesn't exist on the
schematics, while there is actually "VCC3V3_CON" voltage supplying the
display panel.
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + };
> +};
> +
> +&dpi_bridge {
> + status = "okay";
> +};
> +
> +&dpi_to_panel {
> + remote-endpoint = <&panel_in>;
> + bus-width = <18>;
> +};
> +
> +&lcdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcdif>;
> + assigned-clocks = <&clk IMX93_CLK_VIDEO_PLL>;
> + assigned-clock-rates = <332600000>;
> + status = "okay";
> +};
> +
> +&lpi2c2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + touchscreen at 38 {
> + compatible = "edt,edt-ft5406";
> + reg = <0x38>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_touchscreen>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
> + reset-gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
> + touchscreen-size-x = <1792>;
> + touchscreen-size-y = <1024>;
Please add "wakeup-source" property here like in the downstream commit.
With this in place, panel touch can be used to wake up the board from sleep.
Last but not least, can you add the vcc and iovcc supply regulators here
like in the downstream commit:
vcc-supply = <®_vcc_3v3_con>;
iovcc-supply = <®_vcc_3v3_con>;
to get rid of the following warnings:
edt_ft5x06 1-0038: supply vcc not found, using dummy regulator
edt_ft5x06 1-0038: supply iovcc not found, using dummy regulator
Anyway, I tested the display on the segin board with latest linux-next
and your patches. Can report display, touch and backlight work as expected.
Thank you!
Tested-by: Primoz Fiser <primoz.fiser at norik.com>
BR,
Primoz
> + };
> +};
> +
> +&media_blk_ctrl {
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_backlight: backlightgrp {
> + fsl,pins = <
> + MX93_PAD_CCM_CLKO3__GPIO4_IO28 0x1133e
> + >;
> + };
> +
> + pinctrl_lcdif: lcdifgrp {
> + fsl,pins = <
> + MX93_PAD_GPIO_IO00__MEDIAMIX_DISP_CLK 0x50e
> + MX93_PAD_GPIO_IO01__MEDIAMIX_DISP_DE 0x50e
> + MX93_PAD_GPIO_IO02__MEDIAMIX_DISP_VSYNC 0x50e
> + MX93_PAD_GPIO_IO03__MEDIAMIX_DISP_HSYNC 0x50e
> + MX93_PAD_GPIO_IO04__MEDIAMIX_DISP_DATA00 0x50e
> + MX93_PAD_GPIO_IO05__MEDIAMIX_DISP_DATA01 0x50e
> + MX93_PAD_GPIO_IO06__MEDIAMIX_DISP_DATA02 0x50e
> + MX93_PAD_GPIO_IO07__MEDIAMIX_DISP_DATA03 0x50e
> + MX93_PAD_GPIO_IO08__MEDIAMIX_DISP_DATA04 0x50e
> + MX93_PAD_GPIO_IO09__MEDIAMIX_DISP_DATA05 0x51e
> + MX93_PAD_GPIO_IO10__MEDIAMIX_DISP_DATA06 0x50e
> + MX93_PAD_GPIO_IO11__MEDIAMIX_DISP_DATA07 0x50e
> + MX93_PAD_GPIO_IO12__MEDIAMIX_DISP_DATA08 0x50e
> + MX93_PAD_GPIO_IO13__MEDIAMIX_DISP_DATA09 0x50e
> + MX93_PAD_GPIO_IO14__MEDIAMIX_DISP_DATA10 0x50e
> + MX93_PAD_GPIO_IO15__MEDIAMIX_DISP_DATA11 0x50e
> + MX93_PAD_GPIO_IO16__MEDIAMIX_DISP_DATA12 0x506
> + MX93_PAD_GPIO_IO17__MEDIAMIX_DISP_DATA13 0x506
> + MX93_PAD_GPIO_IO18__MEDIAMIX_DISP_DATA14 0x506
> + MX93_PAD_GPIO_IO19__MEDIAMIX_DISP_DATA15 0x506
> + MX93_PAD_GPIO_IO20__MEDIAMIX_DISP_DATA16 0x506
> + MX93_PAD_GPIO_IO21__MEDIAMIX_DISP_DATA17 0x506
> + >;
> + };
> +
> + pinctrl_panel: panelgrp {
> + fsl,pins = <
> + MX93_PAD_CCM_CLKO4__GPIO4_IO29 0x1133e
> + >;
> + };
> +
> + pinctrl_touchscreen: touchscreengrp {
> + fsl,pins = <
> + MX93_PAD_ENET1_MDIO__GPIO4_IO01 0x11e
> + MX93_PAD_ENET1_RD2__GPIO4_IO12 0x1133e
> + >;
> + };
> +};
>
--
Primoz Fiser
phone: +386-41-390-545
email: primoz.fiser at norik.com
--
Norik systems d.o.o.
Your embedded software partner
Slovenia, EU
phone: +386-41-540-545
email: info at norik.com
More information about the linux-arm-kernel
mailing list