[PATCH v3 4/9] dt-bindings: PCI: renesas,r9a08g045s33-pcie: Add documentation for the PCIe IP on Renesas RZ/G3S

[claudiu beznea]

Hi, Bjorn,

On 8/28/25 22:36, Bjorn Helgaas wrote:
> On Thu, Aug 28, 2025 at 10:11:55PM +0300, claudiu beznea wrote:
>> On 8/8/25 14:25, Claudiu Beznea wrote:
>>> On 08.07.2025 19:34, Bjorn Helgaas wrote:
>>>> On Fri, Jul 04, 2025 at 07:14:04PM +0300, Claudiu wrote:
>>>>> From: Claudiu Beznea <claudiu.beznea.uj at bp.renesas.com>
>>>>>
>>>>> The PCIe IP available on the Renesas RZ/G3S complies with the PCI Express
>>>>> Base Specification 4.0. It is designed for root complex applications and
>>>>> features a single-lane (x1) implementation. Add documentation for it.
>> ...
> 
>> Renesas HW team replied to me that there are no clock, reset, or interrupt
>> signals dedicated specifically to the Root Port. All these signals are
>> shared across the PCIe system.
>>
>> Taking this and your suggestions into account, I have prepared the following
>> device tree:
>>
>> pcie: pcie at 11e40000 {
>> 	compatible = "renesas,r9a08g045-pcie";
>> 	reg = <0 0x11e40000 0 0x10000>;
>> 	ranges = <0x02000000 0 0x30000000 0 0x30000000 0 0x8000000>;
>> 	/* Map all possible DRAM ranges (4 GB). */
>> 	dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0x1 0x0>;
>> 	bus-range = <0x0 0xff>;
>> 	interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
>> 		     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>;
>> 	interrupt-names = "serr", "serr_cor", "serr_nonfatal",
>> 			  "serr_fatal", "axi_err", "inta",
>> 			  "intb", "intc", "intd", "msi",
>> 			  "link_bandwidth", "pm_pme", "dma",
>> 			  "pcie_evt", "msg", "all";
>> 	#interrupt-cells = <1>;
>> 	interrupt-controller;
>> 	interrupt-map-mask = <0 0 0 7>;
>> 	interrupt-map = <0 0 0 1 &pcie 0 0 0 0>, /* INTA */
>> 			<0 0 0 2 &pcie 0 0 0 1>, /* INTB */
>> 			<0 0 0 3 &pcie 0 0 0 2>, /* INTC */
>> 			<0 0 0 4 &pcie 0 0 0 3>; /* INTD */
>> 	clocks = <&cpg CPG_MOD R9A08G045_PCI_ACLK>,
>> 		 <&cpg CPG_MOD R9A08G045_PCI_CLKL1PM>;
>> 	clock-names = "aclk", "pm";
>> 	resets = <&cpg R9A08G045_PCI_ARESETN>,
>> 		 <&cpg R9A08G045_PCI_RST_B>,
>> 		 <&cpg R9A08G045_PCI_RST_GP_B>,
>> 		 <&cpg R9A08G045_PCI_RST_PS_B>,
>> 		 <&cpg R9A08G045_PCI_RST_RSM_B>,
>> 		 <&cpg R9A08G045_PCI_RST_CFG_B>,
>> 		 <&cpg R9A08G045_PCI_RST_LOAD_B>;
>> 	reset-names = "aresetn", "rst_b", "rst_gp_b", "rst_ps_b",
>> 		      "rst_rsm_b", "rst_cfg_b", "rst_load_b";
>> 	power-domains = <&cpg>;
>> 	device_type = "pci";
>> 	#address-cells = <3>;
>> 	#size-cells = <2>;
>> 	renesas,sysc = <&sysc>;
>> 	status = "disabled";
>>
>> 	pcie_port0: pcie at 0,0 {
>> 		reg = <0x0 0x0 0x0 0x0 0x0>;
>> 		ranges;
>> 		clocks = <&versa3 5>;
>> 		clock-names = "ref";
>> 		device_type = "pci";
>> 		vendor-id = <0x1912>;
>> 		device-id = <0x0033>;
>> 		bus-range = <0x1 0xff>;
> 
> I don't think you need this bus-range.  The bus range for the
> hierarchy below a Root Port is discoverable and configurable via
> config space.

Thank you for the pointer. I'll update and send a new version.

Claudiu